makemachine.ai
🚀

Roadstoy

Roadstoy is a remote-controlled toy version of the new Tesla Roadster that can briefly jump and flip using compressed air. It drives on an electric motor and is refilled with an ordinary bicycle pump, with no electric pump on board. The compressed-air system (tank, air channels and nozzles) is meant to be printed as one, at most two, 3D-printed parts together with the Roadster-shaped body, with very few screws, hoses and separate brackets. Air outlets are controlled by simple inserted metal pins that open and close single channels. Only untested pressure vessels are ruled out, so printed tanks must be burst-tested before use. So far the concept and research are done, and the current concept is a 1:14 car (307 mm long) in two printed parts. Nothing is built or measured yet, so all performance figures are model estimates. The next step is the mechanical CAD.

Open hardware, CERN-OHL-W 2.0

Project log: 3 updates as text

Concept v1.1

Roadstoy, Concept v1.1: Option 3 “Kick Body”: one tank fill, step by step

v1.1 rebuilds Roadstoy as one integrated printed body in the shape of the 2026 Tesla Roadster. Two printed parts make up the 1:14 car (307 mm long): a main body that holds the tank cells, air channels, five steel-pin valves, nozzles and kick cylinders, and a snap-on nose with the battery and controller. The key finding is that a tank printed inside a toy body holds too little air for jets: with jets alone the car hops only about 3 cm at 6 bar. The recommended Option 3 “Kick Body” uses the same printed tank and pin valves to drive four built-in kick pistons instead; the model gives a hop of …

  • Recommended: Option 3 “Kick Body”, a 1:14 Roadster body in 2 printed parts, with all air parts in one of them
  • Printed in: 3 tank cells, channels, 5 pin-valve seats, 4 kick cylinders and 4 diffuser nozzles like the real car's
  • Kick pistons: about 30–60 cm hop at 3 bar (model). Jets from the same tank: only 3 cm at 6 bar
  • Valves are sliding steel pins (about 25 ms). Without O-rings they would leak the tank empty within seconds

Research v1.0

Roadstoy, Research v1.0: Tesla Roadster in the air on thruster plumes at the 15 Oct 2026 reveal (photo published by NBC News)

The research supports a short, thruster-assisted hop with a controlled landing, possibly with a flip, from one fill of bicycle-pump air. It does not support several seconds of flight on that air. Tesla's public demo (15 Oct 2026) shows a jump of about 27 ft and a landing; the flip is disputed. The main open issue for the toy is pressure: the planned 8 bar is above 70 % of the lowest burst pressure measured for 2 L PET bottles (7.5 bar), and the 0.5 L bottles have no burst data yet, so a burst test must come before the pressure is fixed.

  • Public evidence supports a short hop with a controlled landing, not sustained flight; the flip is disputed.
  • 8 bar is above 70 % of the lowest measured burst of 2 L PET bottles (7.5 bar). Burst-test 0.5 L bottles before fixing the pressure; plan for 7 bar until then.
  • No published datasheet gives valve response times. The lightest quick-exhaust valve found weighs 5–8 g and is rated to 10 bar; its closing speed must be measured.
  • A floor pump can reach 8 bar, but a road-tyre test suggests 50–80 pump strokes for the 1 L tank, not the 40 assumed.

Concept v1.0

Roadstoy, Concept v1.0: The three options in motion: 1 Pop-Flip, 2 Gyro-Jets, 3 Fan-Lift Hybrid

Recommendation: Option 2 "Gyro-Jets". A 1:10 electric RC roadster with two half-litre bottle tanks, pumped to 8 bar with an ordinary bicycle floor pump, four downward air jets at the corners, a rear boost jet and a small gyro controller. Per fill it can hop about 0.75 m and land a backflip upright after about 0.9 s in the air, or boost off with +15 km/h in half a second (estimates from a flight model). Hovering for several seconds is out of reach with pump air at toy scale (about 0.6 s per litre), which matches Tesla's own October 2026 Roadster demo: short jumps and a flip, not sustained …

  • One 1-litre fill at 8 bar gives about 3 N·s of thrust: one backflip or one boost per fill (estimate).
  • Gyro-Jets: about 0.75 m hop, 0.9 s in the air, flip lands upright even with balance errors (simulated).
  • Hovering 3 s would need about 6 litres of tank, so the toy hops and flips, like Tesla's demo.
  • A bicycle floor pump is enough: about 40 strokes per fill, an 8 bar relief valve, a metal tyre valve.