makemachine.ai
🚲

Bike Light

I want to build a bike light that needs no battery. Magnets sit in the spokes close to the hub, and a coil on the fork picks up their motion. Through induction it should generate enough voltage to power two LEDs: a red LED as the rear light and a somewhat stronger white LED as the front light. The housings should be mounted firmly, for example with clamps and screws, so that theft is ruled out or at least made harder. The coil and the LEDs are connected with a simple two-wire cable, which is run along the frame with cable ties. All housings should be printable on a 3D printer. I also want to know what the German StVO regulates here: does it apply to a home-built light too, or only to selling one?

Open hardware, CERN-OHL-W 2.0

Project log: 6 updates as text

Mechanical CAD v1.1

Bike Light, Mechanical CAD v1.1: Front end with magnet ring, pickup and lamp

Version 1.1 rebuilds the bike-light kit so it can go to a 3D printer: a magnet ring clamped to four spokes, a pickup on the fork leg with a ±4 mm slide, a front lamp on the bar that holds the two self-charging cells, and a rear lamp on the seat stay with an 8° rosette. Nothing is drilled into the frame. Every screw, insert and O-ring is in the model. The collision, loose-part, motion, spoke and overhang checks all pass. 21 of the 24 printed part types are ready for test prints. The ring carrier and the pickup housing need a decision on their 1.0 mm magnetic face walls, and the rear puck …

  • Ready for test prints: 21 of 24 printed part types.
  • Not ready: ring carrier MR-01 and pickup housing PU-01 (1.0 mm face wall by design), rear puck RL-01 (thin rim).
  • No drilling: everything is held by clamps, TPU sleeves and security screws; one screw family M4 + M3 (M2 only for the boards).
  • Ring clears the spokes by ≥ 1.91 mm on 28/32/36-hole radial and 3-cross wheels; the gap to the pickup stays 3.0 mm.

Electronics (PCB) v1.0

Bike Light, Electronics (PCB) v1.0: Two simple 2-wire cables: what each one carries

The bike light now has a complete electronics design that is ready to manufacture. A laminated iron-core pickup with two 820-turn coils gives a simulated 4 to 26 V open-circuit at 5 to 30 km/h and up to 1.6 W, and a charger in the front lamp fills two small lithium-titanate cells that also charge in frost and never need a plug. Out of the lamp, the white LED gives about 12 lm at 10 km/h, 70 lm at 20 km/h and 133 lm at 30 km/h without draining the cells, plus up to 2.2 h of standlight; the rear lamp gets a steady current over its own two-wire cable and only needs two red LEDs. Both circuit …

  • Pickup: laminated U-core 35 x 16 x 26 mm with 2 x 820 turns of 0.28 mm wire, about 140 g
  • Simulated open-circuit voltage 4.3 / 8.5 / 12.8 / 17.1 / 25.6 V at 5 / 10 / 15 / 20 / 30 km/h
  • 2 small lithium-titanate cells (rated -30 to +80 °C, safe to charge in frost), recharged only by the wheel
  • Front light out of the lamp: 12 / 39 / 70 / 133 lm at 10 / 15 / 20 / 30 km/h, standlight up to 2.2 h

Mechanical CAD v1.0

Bike Light, Mechanical CAD v1.0: Close-up: magnet ring with two-part arms and pickup on the fork (preview)

The Bike Light v1.0 is modelled in CAD as four groups: a magnet ring on the spokes with a pickup on the lower fork leg, a front lamp on the handlebar, and a rear lamp on the seat stay. The external review found that the ring was not attached, the clamps could not clamp, the front lamp was too high and the report overstated the maturity. Fixed: front lamp height, ring arms (two-part saddle and jaw), pickup and rear clamp gaps and screw holes, GLB format and part nodes, report wording. Not fixed: pickup Y slide, front-lamp stack, rear rosette, front clamp, screws in model and BOM, sections, …

  • Ring to pickup gap: nominal 3.0 mm; minimum 2.0 mm over 72 positions (ring to clamp shell).
  • Pickup housing and core keep 5.0 mm from the lower fork leg; clamp shells touch the leg by design (0.0 mm, deviation from ≥ 5 mm wording).
  • Modelled mass 623.8 g, including 5.0 g nominal counter-plates; about 0.67 kg with coils; target 0.75 kg without cable.
  • Lowest clamp-slip safety 2.0 for the ring arms (conservative friction). Front-lamp values not backed by the model.

Design study v1.0

Bike Light, Design study v1.0: A Orbit: main view, front three-quarter (design draft, rendering)

Bike light study complete, revised after review. Three battery-free directions were modelled and rendered as design drafts: A Orbit (round lamp in a ring bezel), B Blade (linear wedge with an upright rear fin) and C Core (finned block with a window). All three share the same fixed magnet package: 16 magnets on a steel-backed ring of Ø150 mm and a pickup on the fork blade with a 3.0 mm gap. Ben did not answer the vote within 120 minutes, so the recommendation A Orbit was taken (decision by timeout). A Orbit is detailed in stage 2 and was corrected after review (colour variants, floating …

  • Direction A Orbit was chosen by timeout (vote unanswered after 120 minutes); a later vote can change it.
  • All directions share the fixed package: 16 × 12 × 20 × 5 mm N42 magnets, ring Ø150 / Ø90, 3.0 mm gap to the pickup (measured 3.01 mm in A).
  • Open collision: the straight spokes pass through the magnet carrier in all three models (31–33 triangle pairs per spoke in A). Spoke slots or another mount must be decided.
  • Front lens clear aperture Ø32 = 804 mm² and rear reflector ring 748 mm² (placeholder; category Z unverified) meet the 700 mm² rule; front lamp 29.0 mm above the tyre; pickup 6.67 mm from the fork …

Research v1.0

Yes, the German rules apply to a home-built bike light too. StVZO § 22a(2) covers use as well as sale, so a self-built lamp or generator needs an official approval mark before it may be used on public roads; off public roads the rules do not apply. Two routes to a legal home-built unit exist, an individual approval (Einzelgenehmigung) and a discretionary exemption (§ 70 StVZO); neither is documented for a single unit. The concept's 20–30 lm spoke-magnet benchmark is not supported and should be dropped. Two patents are still in force in Germany: a dynamo headlight with a voltage limit …

  • Own use is covered, not only sale (§ 22a(2) StVZO). Off public roads the StVZO rules do not apply.
  • § 67 StVZO: white low-beam front, red rear light and Z-category reflector, no flashing. Removable lights are allowed if fitted in darkness and secured. Generator approval is our reading of § 22a(1) …
  • Approval routes: individual approval under the FzTV via the registration authority and an expert report, or an exemption under § 70 StVZO. Neither is documented for one unit; fees are roughly tens …
  • The concept's 20–30 lm benchmark for a spoke-magnet light is not supported. The commercial Magnic Light uses rim eddy currents and states no spoke magnets.

Concept v1.0

Bike Light, Concept v1.0: How the three options work (animation)

Ben's idea works, but only with an iron core in the pickup: near the hub the magnets move slowly, and a plain coil would make the white LED glow only above about 30 km/h (model estimate). We developed three options that keep the magnets near the hub, the coil on the fork and the 2-wire cable: 1 "Clip magnets" (simplest, faint flashing light), 2 "Magnet ring" (steady light, about 20 lm at 15 km/h and 35–40 lm from 20 km/h, no battery) and 3 "Ring + battery" (constant about 50 lm, also when stopped). We recommend Option 2 "Magnet ring": it is the only option with a steady, useful light and no …

  • Recommendation: Option 2 "Magnet ring", a steady light without a battery.
  • Near the hub the magnets move slowly. A plain coil would only glow above ≈ 30 km/h; an iron core of transformer sheet solves this (estimate).
  • Option 2 gives ≈ 20 lm at 15 km/h and ≈ 35–40 lm from 20 km/h, lights from about 5–8 km/h and has a standlight of 2–4 min (estimates).
  • A commercial light with spoke magnets and a separate generator states 20–30 lm at 15 km/h, in line with our estimate.