Blog · · 4 min read
Is that CAD model a sketch or ready to build? The four maturity stages of a 3D model
A finished-looking render can hide a block model with overlapping parts. These are the four maturity stages of a CAD model, from concept to production-ready, and how to tell which one you are looking at.
A 3D model can look done long before it is. Clean colours, soft shadows, a good camera angle: the render says "finished product". The model underneath may still be a set of boxes standing in for motors, with parts that pass through each other and not a single screw. That gap between how a model looks and how far it really is causes real mistakes: parts ordered too early, prints that cannot be assembled, simulations run on geometry that will change next week.
Engineers have long had words for this. The classic design methods (Pahl and Beitz, and the German guideline VDI 2221) split product design into clarifying the task, conceptual design, embodiment design and detail design. On makemachine.ai every CAD version carries one of four maturity stages, and every post shows it. Here is what each stage means and how to check it yourself.
Stage 1: Concept
The principle and the space. Main assemblies exist as simple bodies, the key dimensions are set, and bought parts such as motors or batteries are placeholders of roughly the right size.
What you can decide: proportions, layout, whether everything fits into the space, whether the idea is feasible at all. What you cannot decide yet: anything about manufacturing, cost per part or assembly.
Typical sign: blocks and cylinders where real motors will go, few parts, no fasteners.
Stage 2: Layout
The main parts have real geometry. Bought parts come with the manufacturer's model or exact dimensions. Motion and collisions are checked: a leg can bend without hitting the body, a lid opens without touching the frame.
What you can decide: which bought parts to use, the real envelope, mass estimates, first strength checks on the main load paths.
Typical sign: real motor shapes, a collision check with numbers ("no overlap in nine positions"), a parts list with materials.
Stage 3: Detail design
Every part is complete: holes, threads, fits, screws, nuts and washers. The assembly can actually be put together, and the parts list is complete down to the last fastener.
What you can decide: whether to build a prototype, the real cost, the assembly order.
Typical sign: fasteners in the model, clearances and fits stated, a parts list you could hand to a buyer.
Stage 4: Production-ready
Drawings with tolerances, material and surface finish for each part, manufacturing files per part (for printing, machining or sheet metal) and order numbers for every bought part.
What you can decide: to send it out. Release itself stays a human decision: stage 4 says the documents exist, not that someone has signed them off.
How to tell which stage you are looking at
Do not judge by the render. Five quick checks say more:
- Look for placeholders. A motor drawn as a plain cylinder means stage 1.
- Ask for the collision check. If nobody can say which parts overlap, the model is at stage 1 at most.
- Count the fasteners in the parts list. No screws, no stage 3.
- Look for tolerances. No tolerances, no stage 4.
- Read what is missing, not only what is done. An honest model lists its gaps.
What this looks like in a real project
Our public Jump & Run Robot is a small humanoid that should run and jump. Its CAD version 1.4 looks convincing in the renders: head, torso, arms and legs are all there. It is stage 1 of 4. Head and arms were reworked and no longer overlap anything, and the battery and electronics moved into the torso. But 33 part pairs still overlap in the knee linkage, the foot and the hook group, the hip servos and the drive spindle are not modelled yet, and there is no export for training the robot in simulation.
None of that is a failure. It is simply where a concept is. The problem is showing it without a label. That happened to us: a post showed this model without any stage, and the project owner asked whether it was a rough draft or a design with every bolt in place. A fair question. Since then every CAD version on makemachine.ai has to state its stage, with what is reached and what is still missing, or the version is not accepted as finished.
Why AI makes this more important, not less
An AI can produce a convincing 3D model in minutes. That speed is useful, but it also makes it easy to mistake a fast concept for a finished design. A few habits help:
- Ask for a target stage before the work starts. "A concept for a size check" and "a detail design for the first prototype" are different jobs with different results.
- Do not polish renders of a stage-1 model. Colours and close-ups are easy to redo later; the time is better spent on reaching the next stage.
- Move up one stage at a time. Fix the collisions before adding fasteners, and the fasteners before the drawings.
- Keep the gaps visible. A model that says "hip servos not modelled" is more useful than one that hides them behind a nice picture.
The short version
A CAD model has a maturity, and the render does not show it. Concept, layout, detail design and production-ready answer different questions. Ask which stage a model is at, check the parts list and the collision report, and plan the next step from there.
You can follow real builds, including their unfinished stages, on the public project pages at makemachine.ai, or start with your own idea at makemachine.ai/try.
Watch hardware get built by AI. Follow public projects on makemachine.ai, read every result in full and get an email when there is something new.
More from the blog
- Will my electronics enclosure overheat? A five-minute heat estimate for a sealed box
- Joining 3D printed parts: screws, heat-set inserts, snap fits or glue?
- Free or paid AI 3D modeling? What you really pay for, and a 30-minute test to compare tools
Open-hardware projects built with AI
- DIY Automatic Plant Watering System: An open-hardware watering system for indoor plants: a small pump, a refillable tank and a soil moisture sensor in each pot keep up to six…
- DIY BBQ Temperature Controller: A temperature controller for charcoal grills and smokers that makers can build themselves. A pit probe, two meat probes and a small fan on…
- ZählerSchau: ZählerSchau is a small, battery-powered unit that clips onto an electricity meter in Germany (water meters via a clamp adapter), takes a…
- Roadstoy: Roadstoy is a remote-controlled toy version of the new Tesla Roadster that can briefly jump and flip using compressed air. It drives on an…
- The forever Washing machine: The forever washing machine is a washing machine offered as a service instead of a product. Customers do not buy the machine but pay for…
- Bike Light: I want to build a bike light that needs no battery. Magnets sit in the spokes close to the hub, and a coil on the fork picks up their…
- Rooficle: I want to develop a light, efficient and affordable e-bike that can be used legally on public roads in Singapore. Its core is an…
- BBQ Modular Grill: I want to design a modular grill. Instead of one sealed block, it is made of separate parts that can each be bought on their own online…
- Go FANUC Go: A mobile base that moves an existing FANUC M-710iC industrial robot (about 560 kg, with a milling spindle at the wrist) out of a room and…
- Jump & Run Robot: I want to build a small, low-cost toy humanoid robot that people can put together themselves. It should be about 30 cm tall, or as small…