The makemachine.ai blog
Product development with AI: what works, what doesn't, and what we learn building real hardware.
-
· 5 min read
Will my electronics enclosure overheat? A five-minute heat estimate for a sealed box
A sealed box keeps water out and heat in. Estimate the temperature inside your electronics enclosure from watts and surface area, and learn what to do when it runs too hot.
-
· 6 min read
Joining 3D printed parts: screws, heat-set inserts, snap fits or glue?
A printed housing is only as good as the way it closes. Compare screws into plastic, heat-set inserts, nuts, snap fits and glue, and learn which one fits your part.
-
· 5 min read
Free or paid AI 3D modeling? What you really pay for, and a 30-minute test to compare tools
AI 3D model tools differ less in price than in what comes out. Learn the three kinds of tool, what free plans usually leave out, and a short test to review any of them.
-
· 6 min read
Prototype machine: what your first build has to prove, and what it can skip
A prototype machine is a question you build. Learn the four kinds of prototype, which one to build first, what to leave out, and how to tell when it has done its job.
-
· 6 min read
Hardware product requirements: the one-page spec that keeps a machine project on track
Before you build a machine, write one page: who uses it, what it must do in numbers, what it must never do, and how you will test it. A practical template with examples.
-
· 6 min read
Waterproof electronics enclosure: what IP ratings promise, and where the water really gets in
IP65 or IP67 on a datasheet does not keep a prototype dry. How to read the rating, design the seal, bring cables through the wall and deal with condensation in a small enclosure.
-
· 5 min read
PCB prototype cost: what really drives the quote for five assembled boards
The bare board is rarely the expensive part of a PCB prototype. Which settings, parts and fees move an instant quote, and how to lower it before you upload the files.
-
· 6 min read
DIY automatic plant watering system: design it to fail dry, not wet
Most DIY plant watering builds work until one part fails. How to choose pump, sensors and safety limits so that any single fault costs one small dose, not a flooded shelf.
-
· 5 min read
Kamado temperature control: the fire needs little air, so the fan's flap matters more than the fan
A ceramic kamado holds heat for hours, which makes it steady and slow to recover from an overshoot. How much air a low-and-slow fire really needs, why a small leak can outrun the fan, and what a flap that closes on its own does for a DIY fan controller.
-
· 5 min read
Contactless bike lights: how a magnet next to the rim makes power, and how much
Lights like the Magnic Light make power from a magnet a few millimetres from the rim. How eddy currents do it, why output drops at low speed, and what to design for.
-
· 5 min read
DIY BBQ temperature controller: probes, a small fan and a loop that does not overshoot
How a controller holds a charcoal smoker at 110 to 135 °C for ten hours: thermistor or thermocouple probes, a small fan with a flap, a PID loop that copes with an open lid, and electronics kept away from the heat.
-
· 5 min read
How high can a toy car jump on bicycle-pump air? Jets vs. pistons in numbers
In the model, a toy car with a 3D-printed air tank hops 3 cm on air jets but 30 to 60 cm on kick pistons. Why jets are limited by the mass of air, why pistons push on the ground, and how to test a printed tank safely.
-
· 5 min read
Does creating 3D models with AI require coding? No, but you need these five skills
No. You describe the part and the AI builds the model. What you need instead: the dimensions that matter, how the part will be made, a feel for fits, and the habit of checking renders and numbers. Plus when reading a little code still helps.
-
· 5 min read
How to make a machine: seven steps from idea to a prototype that runs
How do you make a machine from scratch? Seven steps from idea to working prototype: the job, a physics check, the working principle, CAD, electronics, parts and safety. With a worked lift example and where AI saves time.
-
· 5 min read
How to size a motor: torque, speed, gearing, and stopping on a slope
How big a motor does a machine need? Work from the forces to wheel torque, speed and gear ratio, then check peak and continuous torque. A 700 kg robot base on a ramp shows why holding and braking matter more than raw torque.
-
· 5 min read
BBQ grill design: heat, tipping and parts you can replace
What a charcoal grill has to survive, and how to design one where every part can be bought and replaced on its own: steel that grows when hot, coatings that burn, legs that must not tip, and one shared socket. Lessons from an open-hardware modular kettle.
-
· 5 min read
The parts your PCB order leaves out: batteries, antennas, cameras and cables
An assembled board is not yet a device. The cell, the antenna, the camera module and the cables are bought separately, and each has its own traps: connector series, polarity, flex length, contact side and shipping rules.
-
· 5 min read
Washing machine as a service: designing for three lives instead of forever
Most washers are scrapped after 12 to 13 years, often over repairs nobody makes. What changes when the provider keeps the machine, sells washes and takes it back after nine years: the counter, the tub, the modules and the price per wash.
-
· 5 min read
Ordering PCB assembly: the BOM, the pick-and-place file, and the questions the factory will ask
Gerber files get you a bare board. Assembly needs two more files: a BOM the factory can buy from and a pick-and-place file it can place from. What goes into each, what DNP means, and why the BOM review comes back with questions.
-
· 5 min read
AI CAD vs. traditional CAD: what changes, what stays, and how to use both
AI can now draft parametric 3D models from a description. Where that beats clicking through a classic CAD program, where traditional CAD still wins, and how to move models between the two without losing your design intent.
-
· 5 min read
CAD models for purchased parts: download, borrow, or build from the datasheet?
Most of a machine is bought: motors, bearings, guides, sometimes a whole robot. Where their CAD models come from, what the terms let you do with them, how to check a downloaded STEP file, and when a model built from the datasheet is the better choice.
-
· 5 min read
Ten years on one battery: what really limits battery life in a low-power device
A power budget for a battery-powered meter reader holds a surprise: photos and radio use under two percent of the cell. Self-discharge, heat and one small capacitor decide. What AI can calculate, and what you still have to measure.
-
· 5 min read
Faster quotes for job shops: what AI can read from an RFQ, and what still needs a person
An RFQ lands with drawings, a 3D model and a deadline. How AI can read the package, flag what is missing, check manufacturability and draft the questions back, and why the price stays with the estimator.
-
· 5 min read
3D print, CNC or mold? How to choose the process for your first parts
3D printing, CNC machining, sheet metal, urethane casting or injection molding: how quantity, material, tolerance and shape decide the process for your first parts, and what AI can check in the model before you ask for a quote.
-
· 5 min read
Can you trust AI with engineering numbers? How to keep invented specs out of a hardware project
AI drafts hardware designs fast, but it can also invent a part number or a load rating that looks perfectly real. Where invented numbers creep in, and the checks that keep them out of drawings, BOMs and orders.
-
· 5 min read
Will it print, and will it hold? What AI checks before a part goes on the 3D printer
A correct CAD model can still print badly or snap along its layers. The rules that decide an FDM print (orientation, overhangs, walls, holes and fits) and which of them AI can check and prepare before anything goes on the printer.
-
· 5 min read
AI for RFQs: what a quote-ready package needs, and what AI can prepare
Suppliers quote fast when the RFQ package is complete: solid model, drawing, material, tolerances, finish and quantities. What belongs in it, where packages go wrong, and which parts AI can prepare today.
-
· 5 min read
AI 3D model or real CAD? Mesh vs. solid, STL vs. STEP, and what you can build
Most AI 3D model generators deliver a mesh of triangles, while a machine shop needs an exact solid. What that means for printing, machining and molding, why converting STL to STEP rarely helps, and how to get a model you can build.
-
· 5 min read
What will my prototype cost? Why the first real bill of materials doubled the estimate
A robot concept put its parts at about $500. The first full bill of materials said $1,055. How an AI builds a BOM from the CAD model, separates real prices from estimates, and what to check before you trust the total.
-
· 4 min read
Is that CAD model a sketch or ready to build? The four maturity stages of a 3D model
A finished-looking render can hide a block model with overlapping parts. These are the four maturity stages of a CAD model, from concept to production-ready, and how to tell which one you are looking at.
-
· 5 min read
AI CAD modeling: what the AI needs from you to build the right 3D model
An AI can draft a parametric 3D model in minutes. Whether it is the part you meant depends on what you give it: your own words, real dimensions, your decisions and a check of what was actually built.
-
· 5 min read
Can AI run an FEA? What a stress check found in a jumping robot
A 30 cm jumping robot passed its walking load and failed the landing check. How an AI-run finite element analysis set up the load cases, what it found, and what a simulation still cannot tell you.
-
· 5 min read
Will my hardware idea work? An AI feasibility check on a spoke-magnet bike light
A spoke-magnet bike light sounds simple. A quick physics check showed why a plain coil would barely light the LED, and how three concept options fix it before anyone prints a part.
-
· 5 min read
AI industrial design under hard limits: four renderings of a solar-roof e-bike
How an AI design study turns hard rules into design: four deliberately different directions for a solar-roof e-bike in Singapore, renderings built from measurable 3D models, a compliance check for each, and a vote before CAD starts.
-
· 5 min read
Can AI design a PCB? What works today, and where an engineer still has to look
An honest look at AI PCB design: schematics as code, pin-by-pin netlist checks against datasheets, autorouting, design rule checks and Gerbers, and the parts of a board where an engineer still has to look.
-
· 4 min read
CAD as code: why AI writes the 3D model instead of drawing it
Why an AI that builds hardware should write parametric CAD scripts instead of clicking in a CAD window, what that gives you (exact dimensions, versions, STEP files) and where it still struggles.
-
· 4 min read
What AI can and cannot do when you build a hardware product
An honest look at where AI already helps turn an idea into a physical product, from research to CAD and electronics, and where engineers still have to check every step.
Get new articles by email. Get started free and tick the weekly newsletter.
Open-hardware projects built with AI
- DIY Automatic Plant Watering System: An open-hardware watering system for indoor plants: a small pump, a refillable tank and a soil moisture sensor in each pot keep up to six…
- DIY BBQ Temperature Controller: A temperature controller for charcoal grills and smokers that makers can build themselves. A pit probe, two meat probes and a small fan on…
- ZählerSchau: ZählerSchau is a small, battery-powered unit that clips onto an electricity meter in Germany (water meters via a clamp adapter), takes a…
- Roadstoy: Roadstoy is a remote-controlled toy version of the new Tesla Roadster that can briefly jump and flip using compressed air. It drives on an…
- The forever Washing machine: The forever washing machine is a washing machine offered as a service instead of a product. Customers do not buy the machine but pay for…
- Bike Light: I want to build a bike light that needs no battery. Magnets sit in the spokes close to the hub, and a coil on the fork picks up their…
- Rooficle: I want to develop a light, efficient and affordable e-bike that can be used legally on public roads in Singapore. Its core is an…
- BBQ Modular Grill: I want to design a modular grill. Instead of one sealed block, it is made of separate parts that can each be bought on their own online…
- Go FANUC Go: A mobile base that moves an existing FANUC M-710iC industrial robot (about 560 kg, with a milling spindle at the wrist) out of a room and…
- Jump & Run Robot: I want to build a small, low-cost toy humanoid robot that people can put together themselves. It should be about 30 cm tall, or as small…