Blog · · 5 min read
Contactless bike lights: how a magnet next to the rim makes power, and how much
Lights like the Magnic Light make power from a magnet a few millimetres from the rim. How eddy currents do it, why output drops at low speed, and what to design for.
A bike light that needs no battery, no cable and never touches the wheel sounds like a trick. It is not. Since the Magnic Light was first shown in 2012, several lights have used the same idea: a small magnet rotor sits a few millimetres from the metal rim, and the moving rim makes it spin. People who search for these lights usually want to know two things. Does it really work, and how bright can it get? The physics gives a clear answer to both, and it also tells you what to design for if you want to build one.
How a magnet makes power from a rim it never touches
The rim of most bikes is aluminium, a good electrical conductor. When a conductor moves past a magnet, currents start to circle inside the metal. These are eddy currents. They create their own magnetic field, and that field pushes against the magnet. An eddy-current brake on a train uses exactly this effect to slow the wheels down.
A contactless light turns the brake around. Its magnets sit on a small wheel that can turn freely. The eddy currents in the passing rim drag the magnet wheel along, so it spins like a gear without teeth. Coils next to the spinning magnets then work as an ordinary generator: changing magnetic field in, voltage out. A small circuit turns that voltage into steady current for the LEDs.
So there are two energy steps in a row. The rim pulls the magnet wheel through eddy currents, and the magnet wheel drives a generator. Each step loses some energy, which matters later.
How much power you can expect
The honest answer is: not much, but enough for a modest light. Reports quoting the maker of the Magnic Light put the output at under one watt at 30 km/h. The maker advertised 20 to 40 lux for a pair of lights, and an early review found that roughly right. For comparison, a classic hub dynamo is rated at 3 watts at 6 volts.
Under one watt is less than it sounds like and more than it sounds like. Modern white LEDs turn a watt into well over a hundred lumens, so the electricity is not the limit for being seen. What limits a light that should also show you the road is the optic, the shape of the beam. Half a watt in a good lens can light a path. The same half watt in a bare LED just glows.
Why the light fades when you slow down
This is the point most designs struggle with. The current induced in the rim grows with the rim speed. The force on the magnet wheel grows with that current, and the generator voltage grows with the speed of the magnet wheel. Put together, the electrical power rises roughly with the square of the speed at bike speeds.
In numbers: halve your speed and you get about a quarter of the power. If a light makes 0.8 watts at 30 km/h, it makes about 0.2 watts at 15 km/h and very little when you push the bike uphill. LEDs also need a minimum voltage before they light at all, so at walking pace the light can go dark.
That is why a good contactless light needs a small energy store, usually a capacitor that charges while you ride and keeps the light on at a red traffic light. In many countries such a standlight is expected for the rear light anyway.
Is it really free of drag?
Nothing that makes electricity is free of drag. The energy in the light comes from your legs, plus what the two conversion steps lose. If a light delivers 0.5 watts and the whole chain is 40 percent efficient, it takes about 1.25 watts from the wheel.
Riding at a moderate pace takes something like 100 to 150 watts, so that is around one percent. Users of these lights report that they cannot feel it, which fits the numbers. A hub dynamo under load takes a few watts, so the contactless light is lighter on the legs because it also delivers less light.
What can break the idea
- Carbon rims. Eddy currents need a conductor. Aluminium, steel and magnesium rims work. Full-carbon rims do not.
- The gap. Too far from the rim and the coupling collapses. Too close and the light rubs at the first wobble. A few millimetres is the working range, so the mount must be adjustable and stiff.
- Wheel true and wear. A rim that is a little out of true changes the gap with every turn. On rim-brake bikes, worn brake tracks change it too.
- Mounting points. Many contactless lights clamp onto rim-brake mounts. Disc-brake frames often have no such boss near the rim, so the light needs another mount.
- Dirt. Strong magnets collect steel dust and small metal parts from the road. The housing has to keep them away from the magnet wheel.
Spoke magnets, rim lights, hub dynamos and batteries
- Spoke magnets with a coil on the fork: very simple and cheap, but a plain coil passing a few magnets gives very little power. Our feasibility check on a spoke-magnet bike light showed why it needs more magnets, an iron core and an energy store.
- Contactless rim light: no contact, no batteries, easy to fit on a bike with metal rims. Modest output that drops strongly at low speed.
- Hub dynamo: the most light and the most reliable. It needs a new front wheel and cables.
- Battery light: brightest per gram and easy to move, but it must be charged, and an empty battery is the most common reason for riding in the dark.
If you want to build one
- Check the rims you want to support. Aluminium only, or steel too? Note rim width and how far a mount can sit from the brake track.
- Plan the gap. Design the mount so the gap can be set in small steps and stays put on rough roads.
- Size the magnet wheel and the coils for 15 km/h, not 30. If the light is good at an easy pace, it is good everywhere.
- Add an energy store. A capacitor for the standlight, with a circuit that charges it without starving the LED.
- Spend effort on the beam. A shaped lens does more for road lighting than another tenth of a watt.
- Measure, do not guess. Test on a wheel at 10, 20 and 30 km/h with a fixed load, and measure the light at a fixed distance, so lux numbers mean something.
- Check the rules where you sell. Many countries set requirements for bike lights, from beam shape to standlight.
A bike light is a good first hardware project because every step, from physics check to housing to circuit, is small enough to test. You can follow a bike light project on makemachine, where the idea grows from a sentence to concept, electronics and printable parts.
Watch hardware get built by AI. Follow public projects on makemachine.ai, read every result in full and get an email when there is something new.
More from the blog
- Will my electronics enclosure overheat? A five-minute heat estimate for a sealed box
- Joining 3D printed parts: screws, heat-set inserts, snap fits or glue?
- Free or paid AI 3D modeling? What you really pay for, and a 30-minute test to compare tools
Open-hardware projects built with AI
- DIY Automatic Plant Watering System: An open-hardware watering system for indoor plants: a small pump, a refillable tank and a soil moisture sensor in each pot keep up to six…
- DIY BBQ Temperature Controller: A temperature controller for charcoal grills and smokers that makers can build themselves. A pit probe, two meat probes and a small fan on…
- ZählerSchau: ZählerSchau is a small, battery-powered unit that clips onto an electricity meter in Germany (water meters via a clamp adapter), takes a…
- Roadstoy: Roadstoy is a remote-controlled toy version of the new Tesla Roadster that can briefly jump and flip using compressed air. It drives on an…
- The forever Washing machine: The forever washing machine is a washing machine offered as a service instead of a product. Customers do not buy the machine but pay for…
- Bike Light: I want to build a bike light that needs no battery. Magnets sit in the spokes close to the hub, and a coil on the fork picks up their…
- Rooficle: I want to develop a light, efficient and affordable e-bike that can be used legally on public roads in Singapore. Its core is an…
- BBQ Modular Grill: I want to design a modular grill. Instead of one sealed block, it is made of separate parts that can each be bought on their own online…
- Go FANUC Go: A mobile base that moves an existing FANUC M-710iC industrial robot (about 560 kg, with a milling spindle at the wrist) out of a room and…
- Jump & Run Robot: I want to build a small, low-cost toy humanoid robot that people can put together themselves. It should be about 30 cm tall, or as small…