Blog · · 5 min read
How to size a motor: torque, speed, gearing, and stopping on a slope
How big a motor does a machine need? Work from the forces to wheel torque, speed and gear ratio, then check peak and continuous torque. A 700 kg robot base on a ramp shows why holding and braking matter more than raw torque.
"How big does the motor have to be?" is usually the first question when a machine has to move something heavy. Often it should not be.
Go FANUC Go, an open-hardware project on makemachine.ai, shows why. The task is to move an industrial robot of about 560 kg, with a milling spindle at its wrist, out of a room. Robot and steel base put about 700 kg on four wheels. The base drives straight through a door onto a platform, turns its wheels by 90° and rolls sideways down a ramp with a slope of 1:15, with pauses and safe stops on the way. The motors are servo motors that were already on hand.
Moving 700 kg sounds like a job for a big motor. The numbers say otherwise.
Start with forces, not with a motor catalogue
Write down every force the drive has to overcome, case by case.
- Rolling resistance. Caster makers quote between 1 and 8 % of the load, depending on wheel and floor. Hard polyurethane wheels come in around 3 %. For 700 kg (6.87 kN), that is about 210 N.
- Breakaway. Getting a heavy load rolling from standstill takes 1.5 to 3 times the rolling force.
- Slope. On a 1:15 ramp, gravity pulls the base downhill with about 460 N, 6.7 % of its weight.
- Acceleration. Reaching 0.2 m/s, a slow walking pace, within one second takes another 140 N.
The worst normal case is starting uphill: the base mostly goes down, but must be able to stop, back up and restart on the slope. Climbing at a steady speed takes about 660 N, and about 800 N while accelerating.
Turn forces into torque, speed and power
The first CAD version used wheels of 150 mm diameter, which gives a lever of 75 mm.
- Torque at the wheels is force × radius: 800 N × 0.075 m = 60 Nm, shared by the driven wheels.
- Wheel speed: 0.2 m/s on a wheel with a circumference of 0.47 m is about 25 rpm.
- Power is force × speed: climbing at 0.2 m/s takes about 130 W.
For this machine, torque and power are not the problem.
The gearbox sets torque and speed together
Motors turn fast, wheels slowly, and the gear ratio closes the gap. With a ratio of 100, a wheel at 25 rpm puts the motor at about 2,500 rpm, a normal speed for small servo motors. The torque the motors must deliver is the wheel torque divided by the ratio and by the efficiency of the gearbox.
The project uses worm gearboxes, and a worm gear that holds its load by itself (self-locking) has, by its geometry, a forward efficiency below 50 %. Assume 40 %, and the motors together need 60 Nm ÷ (100 × 0.4) = 1.5 Nm. The research step read about 5.5 Nm of peak torque per motor from the maker's torque curve. There is plenty of margin.
Peak torque, continuous torque, and heat
Motor datasheets give two torques. Peak torque is available for short bursts, such as breaking away or accelerating. Continuous torque is what the motor delivers for as long as you like without overheating, and long loads must fit into it. On this 1.65 m ramp a climb takes about eight seconds, so heat is no issue. On a conveyor that runs all day, it would be the main one.
The hard part: holding and stopping on a slope
On the ramp, gravity pulls with 460 N all the time, about 34 Nm at the wheels. Three questions follow.
What holds the base when the power is off? The first CAD version used planetary gearboxes with a ratio of 40 and separate spring-applied brakes, which close when power is lost. The next version switched to self-locking worm gearboxes with a ratio of 100 and no brakes. That is simpler and cheaper, and the worm holds a parked load by friction.
But self-locking is friction, not a safety function. Gear makers warn that shock and vibration can make a self-locking worm back-drive, and the American Gear Manufacturers Association recommends a brake where a worm gear must not back-drive. Whether a slow base on a 1:15 ramp needs brakes or wheel chocks as a second line is a decision for a person, not for a calculation.
Where does the energy go on the way down? Downhill, the slope pushes harder than the rolling resistance holds back, by about 250 N here, so the drive has to brake. With a gearbox that can be back-driven, the motor then works as a generator and feeds energy into its drive. Without a braking resistor to burn it off, the drive's voltage rises until it trips with an overvoltage fault, right when braking is needed. A self-locking worm avoids this: the slope cannot turn the motor, so the motor drives the base down instead of being driven by it.
How does it stop safely? A stop button that only sends a command is not a safe stop. The research found that the existing motor drives have no "safe torque off", a standard safety function that reliably removes motor torque, so the first design placed two contactors in its place. The base also has a pendulum axle, so all four wheels stay on the ground and carry load. Torque is worth nothing if a wheel slips.
What AI does well here, and what it doesn't
Motor sizing is arithmetic over many cases, and that is where AI helps most. It lists the cases, carries the units through, recalculates when the design changes, and takes values such as peak torque from datasheets with a source instead of guessing. Why that matters is a topic of its own.
What it cannot know is your floor. Rolling resistance on a worn wooden ramp, the real efficiency of a used gearbox and the grip of a wheel are best measured. Pull the loaded base with a luggage scale: the steady reading is the rolling force, and the peak at the start is the breakaway force. The safety concept, with brakes, chocks and who stands where, stays with people.
Checklist for sizing a drive
- List every case: flat floor, start, climb, hold, descent, emergency stop
- Turn forces into wheel torque, speed and power before opening a catalogue
- Pick the ratio from the speeds, then check the torque with the real efficiency
- Fit long loads into the continuous torque, short ones into the peak torque
- Decide what holds the load when the power is off
- Plan where the braking energy goes on the way down
- Measure rolling resistance on the real floor
You can follow the project, with its concept, research and CAD, at Go FANUC Go. How the platform checks whether a part survives its loads is in Can AI run an FEA? If you have a machine of your own in mind, you can describe it here.
Watch hardware get built by AI. Follow public projects on makemachine.ai, read every result in full and get an email when there is something new.
More from the blog
- Will my electronics enclosure overheat? A five-minute heat estimate for a sealed box
- Joining 3D printed parts: screws, heat-set inserts, snap fits or glue?
- Free or paid AI 3D modeling? What you really pay for, and a 30-minute test to compare tools
Open-hardware projects built with AI
- DIY Automatic Plant Watering System: An open-hardware watering system for indoor plants: a small pump, a refillable tank and a soil moisture sensor in each pot keep up to six…
- DIY BBQ Temperature Controller: A temperature controller for charcoal grills and smokers that makers can build themselves. A pit probe, two meat probes and a small fan on…
- ZählerSchau: ZählerSchau is a small, battery-powered unit that clips onto an electricity meter in Germany (water meters via a clamp adapter), takes a…
- Roadstoy: Roadstoy is a remote-controlled toy version of the new Tesla Roadster that can briefly jump and flip using compressed air. It drives on an…
- The forever Washing machine: The forever washing machine is a washing machine offered as a service instead of a product. Customers do not buy the machine but pay for…
- Bike Light: I want to build a bike light that needs no battery. Magnets sit in the spokes close to the hub, and a coil on the fork picks up their…
- Rooficle: I want to develop a light, efficient and affordable e-bike that can be used legally on public roads in Singapore. Its core is an…
- BBQ Modular Grill: I want to design a modular grill. Instead of one sealed block, it is made of separate parts that can each be bought on their own online…
- Go FANUC Go: A mobile base that moves an existing FANUC M-710iC industrial robot (about 560 kg, with a milling spindle at the wrist) out of a room and…
- Jump & Run Robot: I want to build a small, low-cost toy humanoid robot that people can put together themselves. It should be about 30 cm tall, or as small…