Blog · · 5 min read
Ordering PCB assembly: the BOM, the pick-and-place file, and the questions the factory will ask
Gerber files get you a bare board. Assembly needs two more files: a BOM the factory can buy from and a pick-and-place file it can place from. What goes into each, what DNP means, and why the BOM review comes back with questions.
The board files are accepted, the bare board has passed review, and the assembly item sits in the cart. Then one short note: file not uploaded. For turnkey assembly, the factory needs more than the copper layers. It needs to know which parts to buy and where each one goes.
This article walks through the two files that carry that information, the conventions behind most of the questions, and the parts of the job AI can take over.
Three files, three jobs
Gerber and drill files describe the bare board: copper, solder mask, silkscreen, outline and holes. The paste layer in the same set is used to cut the solder stencil.
The bill of materials (BOM) says what to buy: one line per part number, with the designators where it is used and the quantity per board.
The pick-and-place file, also called centroid or CPL file, says where each part sits: designator, X and Y position, rotation and board side. The placement machine is programmed from it.
The three must agree. Every designator in the placement file needs a line in the BOM, and every placed part in the BOM needs a position. Most review questions start where they do not.
What an assembly BOM needs
A useful BOM for assembly has these columns:
- Designators, for example C1, C6, C37
- Quantity per board, which must match the number of designators
- Manufacturer and manufacturer part number (MPN)
- Description or value, such as 10 µF, 10 V, X5R
- Package or footprint, such as 0603 or SOT-23
- Type: surface mount or through-hole
- Notes: anything the buyer should know, like an approved alternative or "do not place"
The MPN is the column that matters most. "10 µF capacitor" cannot be ordered. An MPN can, and it fixes voltage, dielectric, tolerance and package in one go. A distributor's catalog number is a helpful extra in the notes, but the MPN is what the purchaser checks.
Many assemblers publish their own BOM template: the same information, with their column names, a title row and the table starting at a fixed row. Use it. A BOM in the expected layout goes through review faster than one the engineer has to map column by column.
The pick-and-place file
The placement file is usually a CSV with five columns: designator, mid X, mid Y, rotation and layer (top or bottom). The coordinates are the centre of each part, measured from the board origin, and that origin has to be the same one the Gerber files use. State the units. Millimetres are common, but not universal.
Rotation causes most of the trouble. Every footprint library defines its own zero orientation, and positive angles usually mean counterclockwise. The machine does not know that a diode has a direction. So the assembler's engineer checks polarized parts against the silkscreen and the datasheet, and corrects the angle where the library's zero differs from the way the part sits in its tape. Clear polarity marks and pin-1 dots on the silkscreen make this check quick.
Bottom-side parts are where conventions differ most. Some design tools mirror the coordinates of the bottom side, others do not. Say which one you send.
DNP: parts on the board that the factory should not place
DNP means do not populate (also DNI, do not install, or DNF, do not fit). The footprint is on the board, but the assembler leaves it empty. Common reasons: an optional variant, a test part, or a part the assembler cannot source and you fit yourself.
Mark DNP parts clearly instead of deleting them without a word. Otherwise the empty pads look like a mistake, and someone will ask. Some assemblers want DNP lines to stay in the BOM with a note; others want them removed from the BOM and the placement file. Ask which one yours expects.
The ZählerSchau meter reader, an open-hardware project on makemachine.ai, is an example: the assembler does not stock its radio module, so the module is marked DNP in the assembly BOM and fitted by hand.
Turnkey, consigned, or both
In turnkey assembly the factory buys all parts. In consigned assembly you ship them. Partial turnkey mixes both: you supply a few critical or hard-to-get parts, and the factory buys the rest. Whatever you choose, write down who supplies which line.
With turnkey, the parts price is often only final after the BOM review. Until then, the quote may show the assembly cost and leave the components at zero. Placement machines also lose a few small parts during setup and picking, so assemblers usually buy some spares.
Decide in advance how alternatives are handled: not allowed, pre-approved, or only with your written OK. A substitute has to match in form, fit and function, and its price can differ.
The BOM review and its questions
A good assembler does not just load your files. An engineer reads the BOM and the placement file and sends questions. Typical ones:
- The part is out of stock or no longer made. Is this alternative OK?
- The package in the MPN does not match the footprint.
- Where is pin 1, or which side is the cathode?
- The quantity does not match the designators.
- Should this empty footprint stay empty?
Some assemblers send the questions as a spreadsheet with a column for your reply. Answer in that file, and answer quickly: the order waits until every question is closed.
Where AI helps, and where a person still looks
AI is good at the bookkeeping. It can create the BOM and the placement file from the design, check that quantities match designators, convert the BOM into the assembler's template, flag parts that only one supplier has, mark DNP parts by rule, and draft answers to review questions.
Part numbers are the exception to "let it write". An MPN must come from the design data or a catalog, never from memory. We described why in Can you trust AI with engineering numbers?
A person still approves substitutes, checks polarity on the first boards, decides what is fitted by hand, and places and pays for the order.
On makemachine.ai, the electronics step delivers board files, BOM and placement file together. When you order assembly, the platform converts the BOM into the assembler's template and uploads both files to the assembly item in your cart. Checkout and payment stay with you. How the board itself comes about is in Can AI design a PCB?, and what a first parts list really costs is in What will my prototype cost?
Checklist before you order
- Gerber and drill files, with paste layer and board outline
- BOM in the assembler's template, with an MPN for every placed part
- Quantities that match the designators
- Placement file with the same designators, units stated, top and bottom marked
- DNP parts marked, in the form your assembler expects
- Polarity marks and pin-1 dots on the silkscreen
- A clear rule for alternatives
- Someone ready to answer the review questions the same day
Watch hardware get built by AI. Follow public projects on makemachine.ai, read every result in full and get an email when there is something new.
More from the blog
- Will my electronics enclosure overheat? A five-minute heat estimate for a sealed box
- Joining 3D printed parts: screws, heat-set inserts, snap fits or glue?
- Free or paid AI 3D modeling? What you really pay for, and a 30-minute test to compare tools
Open-hardware projects built with AI
- DIY Automatic Plant Watering System: An open-hardware watering system for indoor plants: a small pump, a refillable tank and a soil moisture sensor in each pot keep up to six…
- DIY BBQ Temperature Controller: A temperature controller for charcoal grills and smokers that makers can build themselves. A pit probe, two meat probes and a small fan on…
- ZählerSchau: ZählerSchau is a small, battery-powered unit that clips onto an electricity meter in Germany (water meters via a clamp adapter), takes a…
- Roadstoy: Roadstoy is a remote-controlled toy version of the new Tesla Roadster that can briefly jump and flip using compressed air. It drives on an…
- The forever Washing machine: The forever washing machine is a washing machine offered as a service instead of a product. Customers do not buy the machine but pay for…
- Bike Light: I want to build a bike light that needs no battery. Magnets sit in the spokes close to the hub, and a coil on the fork picks up their…
- Rooficle: I want to develop a light, efficient and affordable e-bike that can be used legally on public roads in Singapore. Its core is an…
- BBQ Modular Grill: I want to design a modular grill. Instead of one sealed block, it is made of separate parts that can each be bought on their own online…
- Go FANUC Go: A mobile base that moves an existing FANUC M-710iC industrial robot (about 560 kg, with a milling spindle at the wrist) out of a room and…
- Jump & Run Robot: I want to build a small, low-cost toy humanoid robot that people can put together themselves. It should be about 30 cm tall, or as small…