Blog · · 5 min read
PCB prototype cost: what really drives the quote for five assembled boards
The bare board is rarely the expensive part of a PCB prototype. Which settings, parts and fees move an instant quote, and how to lower it before you upload the files.
You upload the files for a small board, click through an instant quote and expect the price of a pizza. The bare boards are indeed cheap. Then you tick "assembly", and the total grows by a factor of five or ten. Nothing is wrong with the quote. It just shows that for a prototype, the board is rarely the expensive part.
This article goes through the lines of a typical quote for a small run, for example five boards with two of them assembled. It shows which choices move the price and which do not. The example in the background is the controller board of our public project, a DIY Automatic Plant Watering System, which is at exactly this step: design finished, quotes requested.
The bare board: stay inside the standard
Board factories combine many small orders on one large production panel. Your price is low as long as your board fits the settings that most other orders use. For a simple design these are usually:
- two copper layers,
- standard board material with a thickness of 1.6 mm,
- standard copper thickness,
- green solder mask with white print,
- a basic tin or lead-free tin finish,
- tracks, gaps and holes well above the factory minimum.
Each step away from this list moves the board to another panel or another process, and the price jumps instead of rising slowly. Four layers instead of two, a gold finish, very small holes, an unusual thickness or a special color can each cost more than the whole standard order.
Size matters in steps too. Many factories have a low price class for small boards, often up to about 100 × 100 mm. A board of 100 × 65 mm sits inside that class. A board of 105 × 65 mm may not. If your outline is close to such a limit, a few millimetres are worth an hour of layout work.
Quantity matters less than people think. The minimum is typically five boards, and ten often cost almost the same, because setup dominates. Ordering fewer than the minimum does not exist, so plan what you do with the spare boards. They are useful for measuring, for tests that destroy a board, and for hand-soldered variants.
Assembly: the fees you pay once
Assembly adds costs that do not depend much on how many boards you build:
- Setup. Programming the placement machine and preparing the line.
- Stencil. A thin steel sheet with openings for the solder paste, made for your board.
- Feeder loading. Every different part must be loaded into the machine. Many factories charge a fee per part type that is not already in their standard stock.
For two assembled boards, these one-time fees are most of the bill. That is why the price per board looks shocking at two pieces and reasonable at fifty. It is also why assembling only some of the boards saves less than you hope: the fees stay, only the parts and a little machine time go away.
The number of different parts
After the fixed fees, the strongest lever is the number of unique parts, not the number of parts. Twenty resistors of one value cost almost nothing to place. Twenty resistors of twenty values mean twenty feeders.
Go through the bill of materials before you ask for the quote:
- Can 4.7 kΩ and 5.1 kΩ both become 4.7 kΩ? Often the exact value does not matter for a pull-up or an LED.
- Can all small capacitors share one size and one voltage rating?
- Is each part in the factory's own stock list? Parts from stock are placed without extra handling. Parts the factory must buy for you add purchasing cost, minimum order quantities and days.
Reducing a board from 35 to 22 unique parts is normal for a first design, and it shows directly in the quote.
Parts that need hands
Machines place flat parts on one side of the board quickly. Everything else costs manual work:
- Through-hole parts such as screw terminals, pin headers and large connectors. They are often soldered by hand or in a separate step.
- Parts on both sides. The board goes through the line twice.
- Parts with hidden pads under the body. They may need X-ray inspection.
You do not have to avoid these parts. Screw terminals for pump and sensor cables are the right choice on a watering controller. But decide for each one: is it worth paying the factory for it, or do you solder six terminals yourself in ten minutes? For a prototype, leaving through-hole parts unassembled is a common and sensible saving.
Time and transport
Two lines at the end of the quote are easy to overlook.
Lead time. The standard time is the cheap one. Express production can double the board price. Assembly adds its own days, and a single part that is out of stock can hold the whole order. Check the stock of every part on the day you order, not on the day you drew the schematic.
Shipping and import. For a small order, express shipping can cost more than the boards. Taxes and duties depend on your country and are usually not in the instant quote.
Read the quote before it becomes an order
An instant quote is computed from your files and settings. It is a good tool for comparing variants, and you can use it for that without ordering anything:
- Quote the board alone with standard settings. This is your floor.
- Add assembly for all machine-placed parts and note the one-time fees separately.
- Change one thing at a time: fewer unique parts, through-hole left out, one side only. Watch which change moves the total.
- Quote the same package at two factories. Differences in fees and in part stock are often larger than differences in board price.
After a real order, expect questions. The factory's engineers look at the files and ask about unclear part orientations, replaced parts or footprints that do not match. The final price can change with their answers. Clear files with a complete bill of materials and a placement file keep this round short.
The short version
For a small prototype run, you pay mainly for three things: one-time assembly fees, the number of different parts, and speed. The board itself is cheap if it stays inside the standard. So the best time to lower the price is before the upload: merge part values, pick parts from the factory's stock, keep the outline inside the small price class, and decide which parts you solder yourself.
You can follow how this works out on a real board in our public project: DIY Automatic Plant Watering System.
Watch hardware get built by AI. Follow public projects on makemachine.ai, read every result in full and get an email when there is something new.
More from the blog
- Will my electronics enclosure overheat? A five-minute heat estimate for a sealed box
- Joining 3D printed parts: screws, heat-set inserts, snap fits or glue?
- Free or paid AI 3D modeling? What you really pay for, and a 30-minute test to compare tools
Open-hardware projects built with AI
- DIY Automatic Plant Watering System: An open-hardware watering system for indoor plants: a small pump, a refillable tank and a soil moisture sensor in each pot keep up to six…
- DIY BBQ Temperature Controller: A temperature controller for charcoal grills and smokers that makers can build themselves. A pit probe, two meat probes and a small fan on…
- ZählerSchau: ZählerSchau is a small, battery-powered unit that clips onto an electricity meter in Germany (water meters via a clamp adapter), takes a…
- Roadstoy: Roadstoy is a remote-controlled toy version of the new Tesla Roadster that can briefly jump and flip using compressed air. It drives on an…
- The forever Washing machine: The forever washing machine is a washing machine offered as a service instead of a product. Customers do not buy the machine but pay for…
- Bike Light: I want to build a bike light that needs no battery. Magnets sit in the spokes close to the hub, and a coil on the fork picks up their…
- Rooficle: I want to develop a light, efficient and affordable e-bike that can be used legally on public roads in Singapore. Its core is an…
- BBQ Modular Grill: I want to design a modular grill. Instead of one sealed block, it is made of separate parts that can each be bought on their own online…
- Go FANUC Go: A mobile base that moves an existing FANUC M-710iC industrial robot (about 560 kg, with a milling spindle at the wrist) out of a room and…
- Jump & Run Robot: I want to build a small, low-cost toy humanoid robot that people can put together themselves. It should be about 30 cm tall, or as small…