Blog · · 5 min read
Thermistor, RTD or thermocouple? How to choose the temperature sensor for your device
Most devices measure temperature somewhere. Compare thermistors, RTDs, thermocouples and digital sensors by range, accuracy, wiring and cost, and pick the one that fits your build.
Almost every device measures a temperature somewhere. A grill controller reads the meat and the pit, a battery pack watches its cells, a heater needs to know when to stop, and a sealed box should notice when it gets too hot inside. The sensor looks like a small detail, but picking the wrong type gives you readings that drift, jump or simply stop at the wrong temperature.
There are four common families. This article compares them in plain numbers and gives a short way to choose.
The four families in one paragraph each
Thermistors are small resistors whose value changes strongly with temperature. The common kind for measurement is the NTC thermistor: its resistance falls as it gets warmer. They are cheap, very sensitive, and easy to read with a simple voltage divider and an analog input. The catch is that the curve is far from a straight line, so the firmware needs a formula or a table to turn resistance into degrees.
RTDs (resistance temperature detectors) are also resistors, usually made of platinum. A Pt100 has 100 ohms at 0 °C, a Pt1000 has 1000 ohms. The change is small but almost linear and very stable over years. RTDs are the classic choice when accuracy and repeatability matter.
Thermocouples are two different metals joined at the tip. The joint produces a tiny voltage that depends on the temperature difference between the tip and the place where the wires connect to the circuit. Type K, the most common, gives about 41 microvolts per degree. Thermocouples survive very high temperatures and are tough, but the signal is tiny and needs a dedicated amplifier.
Digital sensors are small chips that measure their own temperature and send the result as a number over a serial bus. No calibration curve, no analog front end. They are limited to the range a chip can survive, roughly from well below freezing to about 125 °C.
Range: the first filter
Start with the hottest and coldest temperature the sensor must see, with margin.
- Up to about 125 °C: all four work. Digital sensors and thermistors are usually the simplest.
- Up to about 300 °C: thermistors in special high-temperature probes, RTDs and thermocouples. Many food and grill probes are thermistor probes built for this range.
- Up to about 600 °C: RTDs and thermocouples.
- Above that, up to roughly 1200 °C: thermocouples. Kilns, exhausts and flames are thermocouple territory.
Check the probe as well as the element. The cable, its insulation and the seal at the tip often set the real limit, long before the sensor itself fails.
Accuracy: what the standards promise
Accuracy is where the families differ most, and where datasheets are easy to misread.
- RTDs have tolerance classes in an international standard. A Class B platinum sensor is allowed ±(0.30 + 0.005 × |t|) °C, so about ±0.3 °C at 0 °C and ±0.8 °C at 100 °C. Class A halves that and more: ±(0.15 + 0.002 × |t|) °C.
- Type K thermocouples under the common North American standard limit may be off by 2.2 °C or 0.75 % of the reading, whichever is larger. At 400 °C, that is ±3 °C. Special-grade wire halves this. That is fine for a pizza oven, but too loose for a lab bath.
- Thermistors are specified by the tolerance of their resistance at one temperature, often 25 °C. Away from that point, the error grows unless you calibrate. With a good part and a correct curve, ±0.5 to ±1 °C over a moderate range is realistic.
- Digital sensors often promise around ±0.5 °C in their best range and more at the ends.
Two errors are not in any datasheet. First, self-heating: the current that reads a resistor sensor also warms it. Keep the measuring current small, and switch it off between readings if you can. Second, placement: a perfect sensor glued to the wrong spot measures the wrong thing. A probe in moving air reads the air; a sensor on a circuit board reads the board.
Wiring and electronics: the hidden cost
The sensor itself is often the cheapest part. The work is in getting a clean signal into the microcontroller.
- Thermistor: one fixed resistor and an analog input. Choose the fixed resistor close to the thermistor's value in the range you care about most, so the resolution is best there.
- RTD: the signal is small, so it needs a precise current source or bridge and a good converter, often a dedicated chip. Long leads add their own resistance, which is why RTDs come with two, three or four wires. Three-wire and four-wire connections cancel the lead resistance.
- Thermocouple: needs an amplifier with cold-junction compensation, because the reading depends on the temperature where the wires meet the board. Use the matching thermocouple wire and connectors all the way to the board; ordinary copper in between adds error.
- Digital sensor: a few wires to a bus, and several sensors can share one line. The easiest option when the range fits.
Noise, distance and the real world
A tiny signal over a long cable picks up noise from motors, fans and switching power supplies. Thermocouples are the most sensitive here: twist the wires, keep them away from motor leads, and filter the reading in software. Thermistors and digital sensors are more forgiving. If the sensor must sit metres away from the electronics, a digital sensor or a four-wire RTD is usually the safest choice.
Also think about failure. A sensor that breaks should give a reading that the firmware can detect, such as an open circuit, not a believable wrong value. A heater that trusts a broken sensor is a fire risk. Add a second, independent cut-off for anything that heats.
A short way to choose
- Below about 125 °C, short distance, simple build: digital sensor or thermistor.
- Food, grill or oven probes up to about 300 °C: high-temperature thermistor probe, or a thermocouple if you need more.
- Best accuracy and long-term stability: platinum RTD with a three-wire or four-wire connection.
- Very hot, rough or fast-changing: thermocouple with a proper amplifier.
- Anything that heats or charges: two sensors or a separate thermal cut-off, never one sensor alone.
How we handle it
On our platform, the electronics step chooses the sensor together with the measuring circuit, checks range and accuracy against the requirements, and plans the wiring and the safety cut-off before a board is drawn. You can see a controller that reads its probes and drives a fan in the public project DIY BBQ Temperature Controller. If your sensor sits inside a closed housing, Will my electronics enclosure overheat? shows how to estimate the temperature it will see.
Watch hardware get built by AI. Follow public projects on makemachine.ai, read every result in full and get an email when there is something new.
More from the blog
- Will my electronics enclosure overheat? A five-minute heat estimate for a sealed box
- Joining 3D printed parts: screws, heat-set inserts, snap fits or glue?
- Free or paid AI 3D modeling? What you really pay for, and a 30-minute test to compare tools
Open-hardware projects built with AI
- DIY Automatic Plant Watering System: An open-hardware watering system for indoor plants: a small pump, a refillable tank and a soil moisture sensor in each pot keep up to six…
- DIY BBQ Temperature Controller: A temperature controller for charcoal grills and smokers that makers can build themselves. A pit probe, two meat probes and a small fan on…
- ZählerSchau: ZählerSchau is a small, battery-powered unit that clips onto an electricity meter in Germany (water meters via a clamp adapter), takes a…
- Roadstoy: Roadstoy is a remote-controlled toy version of the new Tesla Roadster that can briefly jump and flip using compressed air. It drives on an…
- The forever Washing machine: The forever washing machine is a washing machine offered as a service instead of a product. Customers do not buy the machine but pay for…
- Bike Light: I want to build a bike light that needs no battery. Magnets sit in the spokes close to the hub, and a coil on the fork picks up their…
- Rooficle: I want to develop a light, efficient and affordable e-bike that can be used legally on public roads in Singapore. Its core is an…
- BBQ Modular Grill: I want to design a modular grill. Instead of one sealed block, it is made of separate parts that can each be bought on their own online…
- Go FANUC Go: A mobile base that moves an existing FANUC M-710iC industrial robot (about 560 kg, with a milling spindle at the wrist) out of a room and…
- Jump & Run Robot: I want to build a small, low-cost toy humanoid robot that people can put together themselves. It should be about 30 cm tall, or as small…