Blog · · 5 min read
Washing machine as a service: designing for three lives instead of forever
Most washers are scrapped after 12 to 13 years, often over repairs nobody makes. What changes when the provider keeps the machine, sells washes and takes it back after nine years: the counter, the tub, the modules and the price per wash.
The brief came out of talks at an entrepreneurship summit: a washing machine that never breaks. It is an appealing idea. When the project went through its first three steps on makemachine.ai, a process analysis, a concept and a research study, the goal changed. Not a machine that lasts forever, but a machine that the provider owns, that customers pay for by the wash, and that is planned for three lives of about nine years each.
This article explains why, and what that change does to the design.
How long washing machines really last
The German Environment Agency (UBA) looked at how long large household appliances such as washers, dryers and fridges stay with their first owner. The average first useful life fell by about a year, to 13 years. The share of appliances replaced within five years because of a defect rose from 3.5 % in 2004 to 8.3 % in 2013. The study found no proof of defects built in on purpose. Obsolescence had many causes, from wear to the wish for a better machine.
The project's own research found a similar picture in a German household survey: discarded washers were about 12 years old on average, and one in five was younger than five years. In repair records, electronics faults were fixed most often, in about half of the cases. Drum, tub and bearing faults were fixed least often, in roughly one case in four.
There is a mechanical reason for that. On many machines the drum bearings sit in the outer tub. If the two tub halves are welded instead of bolted, a worn bearing means a whole new tub, and the repair can cost close to a new machine. So the machine goes to scrap with a working motor, a sound frame and a sound drum.
Why "forever" is the wrong target
A machine built to last 30 years in one household has three problems. Wear parts still wear. The electronics and the efficiency stay at the level of the year it was built. And the buyer pays for durability up front without being able to see it in the shop.
Selling the use instead of the machine changes who carries those problems. If the provider keeps ownership and earns per wash, every extra year of service is the provider's gain, and every early failure is the provider's cost. Durability stops being a promise in a brochure and becomes part of the business.
The concept still sets a limit, because an open-ended promise cannot be planned or priced. Each machine is exchanged after about nine years or 3,000 washes. It is then remanufactured: worn and outdated parts are replaced, the machine is tested, and it goes out again. Three use periods per frame add up to about 27 years. The nine years and 3,000 washes are a target to test in a pilot, not a verified figure.
What changes in the design
The concept compares three ways to start:
- Retrofit counter. A stock machine whose tub can be opened, plus a sealed wash counter outside the machine. Nothing inside is changed, so it works with today's machines and spare parts. This is the recommendation for a pilot with about 300 machines.
- Semi-pro machine. A semi-professional machine, kept as the option for shared laundry rooms, where many households use one unit.
- Reman-ready modules. A machine specified with a manufacturer so that the parts that wear or age can be swapped as modules. The concept suggests starting this from month 12 of the pilot.
Whichever path is chosen, the same rules apply when a machine has to come back and go out again. The tub must open, so bearings and seals can be replaced. Wear parts should be reachable without taking the whole machine apart. Fasteners should be standard and screwed, not glued. And the counter has to be trusted by both sides: the household must see what it pays for, and the provider must know that the count was not changed.
Paying per wash: where the math gets honest
Washes are sold as points weighted by temperature. That reflects cost: most of the energy in a wash goes into heating the water, so a hot wash costs more points than a cool one.
The concept's estimates are plain about the economics. The full cost per wash comes to about €0.29 net for the retrofit option and €0.24 for the module option, both at 3,000 washes per period. At a price of €0.30 per point, the retrofit option only breaks even from about 282 washes a year. An average household runs about 220. So a pay-per-wash service pays off with heavy users, such as large families and shared laundry rooms, and not with the average household. The research also found that usage offers for washers already exist in Germany at about €15 to €25 a month, but mostly as rentals, not per wash.
These are estimates. The pilot exists to replace them with measured numbers.
The rules point the same way
EU ecodesign rules already require washing machine spare parts to stay available for ten years after the last unit of a model is placed on the market. The EU right-to-repair directive, which member states had to turn into national law by 31 July 2026, lists household washing machines among the products whose manufacturers must offer repair. Both make a machine built for take-back and reissue easier to plan, because the parts for a second and third life have to exist anyway.
What the AI did, and what it flagged
The three steps so far were done with AI: the process analysis, the concept with three options and a pilot plan, and the research on failure causes, rules and replaceable modules. The research also checked the starting claims. Some statements attributed to summit speakers could not be confirmed in any published source, and the project says so instead of repeating them.
What the AI did not do is decide. The points model and the list of replaceable parts are open decisions for a person, and they come before any CAD work.
Checklist for a hardware product sold as a service
- Define the use period in years and in cycles
- Count use in a way both sides trust
- Make the housing and the tub separable, and keep wear parts reachable
- Plan take-back, cleaning, testing and reissue before launch
- Price against real usage, not against the average household
- Check spare-part and repair duties in your market
You can follow the project, with its research and concept, at The forever washing machine. How an AI checks whether an idea can work at all is in Will my hardware idea work?, and what a first parts list really costs is in What will my prototype cost? If you have an idea of your own, you can describe it here.
Watch hardware get built by AI. Follow public projects on makemachine.ai, read every result in full and get an email when there is something new.
More from the blog
- Will my electronics enclosure overheat? A five-minute heat estimate for a sealed box
- Joining 3D printed parts: screws, heat-set inserts, snap fits or glue?
- Free or paid AI 3D modeling? What you really pay for, and a 30-minute test to compare tools
Open-hardware projects built with AI
- DIY Automatic Plant Watering System: An open-hardware watering system for indoor plants: a small pump, a refillable tank and a soil moisture sensor in each pot keep up to six…
- DIY BBQ Temperature Controller: A temperature controller for charcoal grills and smokers that makers can build themselves. A pit probe, two meat probes and a small fan on…
- ZählerSchau: ZählerSchau is a small, battery-powered unit that clips onto an electricity meter in Germany (water meters via a clamp adapter), takes a…
- Roadstoy: Roadstoy is a remote-controlled toy version of the new Tesla Roadster that can briefly jump and flip using compressed air. It drives on an…
- The forever Washing machine: The forever washing machine is a washing machine offered as a service instead of a product. Customers do not buy the machine but pay for…
- Bike Light: I want to build a bike light that needs no battery. Magnets sit in the spokes close to the hub, and a coil on the fork picks up their…
- Rooficle: I want to develop a light, efficient and affordable e-bike that can be used legally on public roads in Singapore. Its core is an…
- BBQ Modular Grill: I want to design a modular grill. Instead of one sealed block, it is made of separate parts that can each be bought on their own online…
- Go FANUC Go: A mobile base that moves an existing FANUC M-710iC industrial robot (about 560 kg, with a milling spindle at the wrist) out of a room and…
- Jump & Run Robot: I want to build a small, low-cost toy humanoid robot that people can put together themselves. It should be about 30 cm tall, or as small…