makemachine.ai
DA

DIY Automatic Plant Watering System

An open-hardware watering system for indoor plants: a small pump, a refillable tank and a soil moisture sensor in each pot keep up to six plants watered while you are away, and it warns you before the tank runs dry. Built step by step on makemachine.ai: concept, research, mechanical design, electronics, sourcing and a presentation.

Open hardware, CERN-OHL-W 2.0

Project log: 4 updates as text

Electronics (PCB) v1.0

DIY Automatic Plant Watering System, Electronics (PCB) v1.0: Two switches per pump: how the board limits every dose

The main board of the watering station is designed, routed and checked: 100 × 65 mm, two layers, all parts on one side, ready for turnkey assembly. An ESP32-S3 development board plugs on top; the board drives six pumps, six soil sensors, the scale amplifier, a leak probe, a buzzer and the status LED from one 12 V adapter. Its key feature is a fail-dry layer in hardware: every pump needs two switches in series, the main switch is held by a timer that cuts pump power after 56 s per start, and a wet drip tray cuts power and sounds the buzzer without any software. All design checks pass and …

  • Main board 100 × 65 mm, 2 layers, 137 parts on one side; fits the space reserved in the mechanical design
  • Pump power only through a timer-held main switch: at most 56 s per start (28 s option)
  • Wet drip tray cuts pump power and sounds the buzzer without software
  • Current and voltage sensing find a stuck switch, a missing or a blocked pump before water moves

Mechanical CAD v1.0

DIY Automatic Plant Watering System, Mechanical CAD v1.0: Watering station, assembled

The watering station is a complete parametric CAD model at stage 2 (rough design): drip tray, a scale on a 20 kg load cell, tank, pump deck with six pumps and the electronics, and a plant kit for each pot. Two reviews found four defects, and all are fixed: the tilt stops keep 0.57 mm of air with a full tank, the load-cell amplifier sits in the dry compartment, the base keeps about 1.7 mm of air to the tray floor, and the cable loop at the back drips 6.5 mm inside the tray rim. All 33 checks pass, among them 0 penetrations in four motion states and support-free printing for all 24 printed …

  • Complete parametric model: 232 parts, 4 motion states, 24 print-ready parts, 62-row parts list
  • 33 of 33 checks pass; 0 penetrations in all states, flexible tube and cable loops included
  • Review round 1 fixed: tilt stops keep 0.57 mm of air under full load; amplifier moved out of the drip tray
  • Review round 2 fixed: base keeps about 1.7 mm of air to the tray floor; rear cable loop drips 6.5 mm inside the rim

Research v1.0

We re-checked the key figures of the concept against the library PDFs, which now include most of the watering documents. The main points hold: two manufacturer manuals confirm the siphon risk when a pump stops with its outlets below the water level, and the sensor's voltage and waterproofing limits and the pathogen counts are correct. Two claims need fixing: the leak sensor cited for rain water does not cover rain water, and the 3.6–97 mL range merges two plant species. Two service searches added peer-reviewed sensor and dosing data and a set of patents that are close to parts of the …

  • Siphon risk confirmed: a pump that stops still lets water run through a drip system whose outlets sit below the water level (two manufacturer manuals agree).
  • The tank-fed Tropf-Blumat system needs its water at least 0.5 m above the plants and its maker says it may not be used indoors, so it is not a model for indoor use.
  • Capacitive moisture sensors: 3.3–5.5 V supply, 0–3.0 V output, board not waterproof. A 2025 study of four sensors in three substrates finds each substrate needs its own calibration; the DFRobot …
  • Irrigation water sources carry 17 Phytophthora and 26 Pythium species, so run-off must not go back into the supply.

Concept v1.0

DIY Automatic Plant Watering System, Concept v1.0: The three options step by step: how each keeps water where it belongs

Three ways to build a DIY watering system for one to six indoor plants that fails dry: no single fault – power cut, stuck valve, dead sensor, stuck pump switch or loose tube – may release more than one small dose of water. Recommended: Option 1 – Self-closing pump per plant. Each plant gets its own small peristaltic pump whose rollers keep the tube pinched shut whenever it stops, so nothing can siphon and there is no valve that could stick; it works with existing pots and saucers wherever they stand. All options share a safety layer: a hardware timer that limits every pump pulse, a leak …

  • Recommended: Option 1 – Self-closing pump per plant: no valves, and every tube stays pinched shut during a power cut.
  • Core rule 'fail dry': any single fault releases at most one small dose (estimate: 20–30 mL).
  • Every dose is checked twice: the tank must get lighter and the soil wetter, otherwise that plant is locked and an alert goes out.
  • A hardware timer limits each pump pulse even if a switch sticks or the controller hangs; a wet drip tray cuts pump power at once.