makemachine.ai

Jump & Run Robot

I want to build a small, low-cost toy humanoid robot that people can put together themselves. It should be about 30 cm tall, or as small as the available motors allow. You drive it with an Xbox controller over Bluetooth. It walks, runs and jumps, and an on-board controller that learned its balance in simulation keeps it upright.

Open hardware, CERN-OHL-W 2.0

Project log: 19 updates as text

Making-of v1.1

Jump & Run Robot, Making-of v1.1: Vertical teaser, 57.8 s (simulation and 3D model)

A 3:17 project film (196.9 s) shows the jump-and-run robot with a spring-loaded torso, tested in simulation. The simulation gives a typical jump of 13.3 cm, and the target of 13 to 15 cm is met only in its lower half, while the top stop shock reaches 122 g against a 100 g target. Higher jumps were only shown as first, untrained tests, with harder landings or a scripted tuck. Nothing is built or published yet; the film ends by asking viewers whether 13.3 cm is enough. A 57.8-second vertical teaser is included as a deviation from the length rule.

  • Spring-loaded torso: two springs store 12 J, a servo releases the hook, take-off 0.42 s after the button
  • Robot training (simulation): typical jump 13.3 cm; 9 of 10 jumps 12.3 to 14.8 cm; feet clear 10.3 cm
  • 127 of 128 standing jumps land and stay up (simulation)
  • Target 13 to 15 cm met only in the lower half; top stop shock 122 g vs 100 g target

Robot training v1.2

Jump & Run Robot, Robot training v1.2: Walk, run and jump on gamepad commands

In simulation, the 3.13 kg Jump & Run Robot from CAD v1.6, now with head and arms, learned to walk, turn, side-step, run up to 1.2 m/s and jump on gamepad commands, all with one learned controller. The spring torso throws the body 13.3 cm up (median of 128 runs with random variations and pushes), from standing or from slow walking, and the robot lands and stays on its feet in 98–100 % of the runs; running at 0.8 m/s worked in all 128 runs, at 1.0–1.2 m/s in 94–96 %. So the concept's jump and speed targets are reachable. The limits are the drives: the knee motor works at 1.4–1.8 times its …

  • Walks 0.3 m/s, turns, side-steps and runs up to 1.2 m/s in simulation
  • Jumps 13.3 cm from standing or walking and lands in 98–100 % of runs
  • One controller for everything, 50 times per second, 6 µs per step
  • Head and arms are on the robot; the arms swing gently and go down before each jump

Mechanical CAD v1.6

Jump & Run Robot, Mechanical CAD v1.6: Overview: Jump & Run Robot v1.6

v1.6 Nachbesserung: boot shells are closed and watertight, 13 hulls rebuilt per the wrap/drum style with one deviation (calf wade envelope). Not met: magenta motor check (hip joints visible, 460 px front, 621 px leg close-up), two hull overlaps of 376 and 432 mm³, knee linkage clearance (S1c, up to 208 mm³ at 115°). Mass 3.134 kg (BOM 3133.59 g). Halt tests stand and crouch pass; crouch rbkp variant fails.

  • Option (a) chosen: structural changes S1–S4, left leg mirrored to right.
  • BOM total 3133.59 g = robot model mass 3.13359 kg (0.0 % deviation); 506.7 g are placeholder/open masses without geometry.
  • Hulls: 319.05 g PETG (13 hulls, volume × 1.27e-3 g/mm³ before support factor).
  • Boot shells: watertight, one body each (degenerate faces were the cause of the earlier open-edge result).

Mechanical CAD v1.5

Jump & Run Robot, Mechanical CAD v1.5: Front view

v1.5 delivers a simulation model of the robot with 13 joints, 16 bodies, a mass of 2.868 kg and 8 named poses, and the stand and crouch halt tests pass. The leg shells, knee layers and the 33 overlapping part pairs from v1.4 remain open, so requirements V2 (trainable) and V3 (legs packaged) are not met. The external review found V1 wrongly marked as not met; it is now met with model evidence. The halt-test contact rule was changed after a failure, and this change is disclosed in the full report. Maturity: stage 1 of 4 (concept).

  • Model loads; mass 2.868 kg matches the parts list (0.0 % deviation).
  • Stand and crouch hold for 5 s; the crouch with reference gains falls.
  • Collision meshes and reference joint and sensor names added after the review.
  • Leg shells not built; motors visible; V3 not met.

Mechanical CAD v1.4

Jump & Run Robot, Mechanical CAD v1.4: Front view, parametric draft (v1.4)

The v1.4 parametric draft of the jump-and-run robot now has a rounded head with a black visor and two eyes, closed shoulder housings with arms and fists, four battery cells outside the spring column, and both foot keels. The model has 85 parts, weighs 2361.5 g and is 412.97 mm high. It is still at maturity stage 1 of 8: 33 part pairs in the knee linkage and hook group still overlap, and the robot export, the packed legs and the checks are not done yet.

  • Vorgabe 1 (head and arms) is met in the model: visor, eyes and shoulder housings have no overlaps.
  • Vorgabe 2 (trainable export) is not met: no simulation model/URDF yet, the knee linkage must be layered first.
  • Vorgabe 3 (packed legs) is not met: shells, shorts, knee pads and boot are still missing.
  • Overlaps dropped from 74 to 33 pairs; all remaining ones are in the knee linkage and the hook group.

Mechanical CAD v1.3

Jump & Run Robot, Mechanical CAD v1.3: Spring-torso module (unchanged from v1.1)

v1.3 is still a partial model: stage 1 of the rough design, 58 solids, 1516.6 g for the placed parts. The review fixed the six-bar housing clearance (30.0 mm to the housing, 11.5 mm to the hub), removed the arm overlap with the pelvis and slider plates, seated the hip yaw bearing and hub in the pelvis plate, labelled the smart-joint masses as estimates and fixed the diagram title. The knee does not meet the transmission-angle limit: minimum 21.5 deg at 130 deg knee flexion against 30 deg. This is a decision for the robotics lead (offenefragen). The torso, the total mass and height, the cost …

  • Knee transmission angle minimum 21.5 deg at 130 deg flexion, limit 30 deg: A5 not passed
  • Knee forces up to 450 N (stage 1) and 449 N (stage 2); ratio 0.60-0.96 in absolute value
  • Six-bar clearance met: 30.0 mm to the housing, 11.5 mm to the hub (minimum, envelope model)
  • Knee gap 70.0 mm (limit 60 mm, envelope model, estimate); ankle rod 80.000 mm, ratio 1.000

Mechanical CAD v1.2

Jump & Run Robot, Mechanical CAD v1.2: Spring-torso module (unchanged from v1.1)

CAD v1.2 is not delivered as a complete robot. This is the rework state after the review of 2026-10-15. The gear set 14/10/34 (11.76:1) now passes the mesh check with 0.10 mm planet backlash. Everything that needs the knee, the GIM position and the thigh (step 5 of the rough design) is still open, so the 3D model, mass, height, cost, robot export and v1.2 images are not delivered. The v1.1 model, report and data files that could be mistaken for v1.2 were removed from the results; the v1.1 originals stay in the inputs.

  • v1.2 is not complete: legs, GIM, shells, shorts, boots and arms B are open (reifegrad 1)
  • Gear set 14/10/34: without backlash 0.0221 mm2 overlap (fails 0.02 mm2); with 0.10 mm planet backlash 0.0021 mm2 (passes)
  • Removed v1.1 files: robot model, leg fabrication parts, broken 342 mm model, v1.1 mass/cost/check files
  • Open from review: GIM vs roll plate collision, knee four-bar near dead centre, leg checks A7-A12, mass and cost

Concept v1.6

Jump & Run Robot, Concept v1.6: Option 1 Hidden Joints: the jump in slow motion, from cocked to reload

Recommended is Option 1 "Hidden Joints": a bought Steadywin joint motor lies flat in the top of each thigh and drives the knee through a hidden rod, the ankle motor moves onto the knee axis, and load-carrying printed shells give the legs a strong, rounded shape. The legs now end ±106 mm from the centreline instead of ±146 mm, no motor sticks out, and each arm gets a small servo, a 125 mm arm and a fist. No leg spring is left or needed, and the torso jump mechanism stays exactly as before. The price is about 0.25 kg more mass (3.22 kg) and roughly 2 cm less standing jump, 13–15 cm expected at …

  • Recommended: Option 1 Hidden Joints, with the knee motor in the thigh top, the ankle motor on the knee axis and rods inside load-carrying printed shells.
  • Legs ±106 mm from the centreline instead of ±146 mm; no motor sticks out.
  • No leg spring is left and none is needed; the torso jump mechanism stays unchanged.
  • Estimated 3.22 kg (+0.25 kg), a 13–15 cm standing jump at 12 J (before: 15–17 cm) and a landing peak of about 630 N.

Mechanical CAD v1.1

Jump & Run Robot, Mechanical CAD v1.1: CAD v1.1 standing and cocked (front left)

CAD v1.1 builds the Concept v1.5 spring torso into the CAD v1.0 robot: the upper body slides on two Ø8 steel rods, two springs store 12.06 J over 80.3 mm, a servo-released steel hook holds them, and a Tr8x2 lead screw with a 12 V gearmotor re-cocks the torso in 30.8 s. The shanks and feet are now aluminium tube parts, because the printed shank failed in FEA v1.0 (landing peaks about 600 N), and a lateral stop limits hip roll to ±15°. The robot weighs 2968 g, 725 g (+32 %) more than the concept's 2243 g, and stands 388 mm tall, 88 mm over the 300 mm envelope, so robotics should retrain with …

  • Spring torso: 2 springs on Ø8 rods, 12.06 J over 80.3 mm, re-cocked by a lead screw in 30.8 s
  • Aluminium-tube shanks and feet replace the printed shank that failed in FEA v1.0
  • Mass 2.97 kg: +725 g (+32 %) over Concept v1.5
  • Height 388 mm standing, 88 mm over the 300 mm envelope

Concept v1.5

Jump & Run Robot, Concept v1.5: Option 2 spring torso, side view

The robot can be about 0.2 kg lighter (legs, motors, battery), but the lighter variants jump higher and land harder. Recommended: Option 2 at 2.24 kg with aluminium shanks and feet, lateral stop, no leg push in the first build. Walking and running at 2.0 kg are not tested.

  • Model mass 2.243 kg; planning total 2.592 kg (missing gearmotor 202 g, pelvis rods and fasteners 147 g); 104 g gap to CSV open.
  • Closed-form jump matches training sim: 12 J 18.8 cm (sim 18.4 cm), 15 J 23.1 cm (sim 21.9 cm). Rest mass costs about 1.6 cm per 100 g; slider mass gains about 1 cm per 100 g.
  • Lighter legs and 35 mm motors: 2.09 kg, 21.4 cm, landing about 600 N.
  • Lighter battery (2 cells out): 2.10 kg, 17.3 cm, landing about 540 N.

Robot training v1.1

Status 2026-10-13: the standing-jump part (T4) and the end-stop model choice are done in simulation. Gait training, the jump from walking and running, landing statistics beyond the standing case, thermal, battery, fault cases, videos and the remaining output files are NOT done yet. Nothing below is a finished answer for those items.

Concept v1.3

Jump & Run Robot, Concept v1.3: Instant jump in 5 steps: Option 2 "Spring torso" and Option 1 "Battery hammer" (animated)

v1.3 replaces the crouch-and-charge leg jump with Ben's idea: a spring-loaded torso that fires the moment A is pressed, with no crouch (take-off about 50–70 ms after the press, est.). I recommend Option 2 "Spring torso": the whole upper body with the battery (0.63–0.76 kg) slides 80 mm above the pelvis, two steel springs throw it up against an end stop, the stop pulls the stiff, simple legs off the ground, and a small motor reloads it in 2.5–5 s while the robot walks on. Physics sets the price: only about 27 % of the spring energy becomes jump, so the springs store 12–15 J, and the robot …

  • Recommended: Option 2 "Spring torso": the whole upper body with the battery is the moving weight, 80 mm stroke
  • Press A and it jumps at once: take-off about 50–70 ms after the press, no crouch (est.)
  • Jump (est.): 13–17 cm CoM rise at 12 J, 16–21 cm at 15 J; feet clear 19–29 cm; lower than v1.2
  • Physics: only ~27 % of the spring energy becomes jump, so the springs must store 12–15 J

Simulation (FEA) v1.0

Jump & Run Robot, Simulation (FEA) v1.0: Spannung gebrauch

Die FEA ist fertig, und die Ergebnisse stehen in the full report und the results. Das Ergebnis ist negativ: Gebrauch besteht überall, Landung besteht nur am Oberschenkel, seitlicher Missbrauch besteht bei keinem Teil.
| Teil | Gebrauch (39,7 N) | Landung (300 N) | Seitlich (100 N) |
|---|---|---|---|
| Oberschenkel | 23 | 3,1 | 0,26 |
| Unterschenkel | 4,8 | 0,63 | 0,14 |
| Fuß | 8,8 | 1,17 | 1,69 |
Zahlen sind Sicherheitsfaktoren (25 MPa / max. Mises abseits der Lager), Ziel ≥ 2.
• Unterschenkel, Landung: Die Spannung von 39,7 MPa sitzt bei (3,0; −4,1; −16,4) mm und ist nahezu konvergiert. …

  • Service load (2 x body weight, 39.7 N): passes for all three parts (safety 4.8 to 23).
  • Landing load (300 N): fails for the shank (safety 0.63) and the foot (safety 1.17). The thigh passes (safety 3.1).
  • Lateral misuse (100 N): fails for all parts (safety 0.14 to 1.7).

Mechanical CAD v1.0

Jump & Run Robot, Mechanical CAD v1.0: Hopper v1.0 in the standing pose

Version 1.0 turns the 30 cm "Hopper" concept into a parametric CAD model with real geometry for every main part: printed leg frames, six identical smart joints (MN4004 outrunner with a printed 10.24:1 planetary gear), a spring-loaded knee four-bar with a three-notch latch, and a torso with battery and electronics. Standing, the robot measures 291.2 × 112.5 × 299.6 mm (width × depth × height); all 8 exported poses are collision-free; the exported simulation model and URDF load in the physics simulation, and the simulated robot stands with the trained controller's PD gains. It weighs 2.02 kg …

  • Standing envelope 291.2 × 112.5 × 299.6 mm, inside the 300 mm cube
  • Mass 2024.4 g (concept 1450 g); parts cost $1055.08 (target about $500)
  • Six identical smart joints: MN4004 KV300 + printed 2-stage planetary gear, i = 10.24
  • Knee four-bar with torsion spring and latch notches at knee 95/115/135°, one release servo for both legs

Research v1.0

Jump & Run Robot, Research v1.0: Legolas, open biped (photo from its GitHub page)

No small humanoid is verified to walk, run and jump at about 30 cm. The closest is Legolas (about 30 cm, hobby servos), which walked only with a support gantry. The best verified small walker, Open Duck Mini, stands about 42 cm and learns its walking in simulation, then runs the policy on a Raspberry Pi Zero 2 W. Learned walking transfers zero-shot to miniature humanoids of OP3 size (Haarnoja et al., 2024), and a smartphone-based 1.8 kg humanoid costs about 400 USD (PhoneBot, 2026). The main risk is actuator torque: a community build log reports a real servo stalls far below the simulated …

  • Closest 30 cm platform (Legolas) walked only with a gantry; no published 30 cm humanoid is verified to run or jump
  • Learned balance control is the common method: zero-shot transfer on OP3-class robots (Haarnoja 2024), ONNX policies on a Raspberry Pi Zero 2 W (Open Duck Mini), PPO on a smartphone (PhoneBot)
  • Servo torque gap: real STS3215 stalls at 1.86 N·m, simulation allows 3.23 N·m (secondary source, to be checked)
  • Knee and ankle drives in patents: actuators on the upper leg with linkages (UBTECH), linear screw actuator (Boston Dynamics), tendon drive (Droidup, pending); no freedom-to-operate statement

Robot training v1.0

Jump & Run Robot, Robot training v1.0: Charge jump over a 30 cm bar with landing (real time + 5× slow motion)

The charge jump and the landing work in simulation. In the full hold-A → crouch → latch → release sequence, 256 randomised robots gain 0.34 m of CoM height after take-off (median; all ≥ 0.25 m) and clear 0.42 m with the feet (99.6 % ≥ 0.30 m). 98 % land without falling at 2.5 m/s. Walking, running at 0.8 m/s with a real flight phase, and the small hop also pass. CAD can go ahead, with five changes: ankle dorsiflexion to −70°, a hard knee extension stop, a latch designed for ≈ 6.5 N·m at the crank, a stronger battery path (the 4S1P pack sags below 12 V at 36–46 A push-off pulses), and smart …

  • Charge jump (T5) passes in simulation: CoM rise 0.34 m after take-off, foot clearance 0.42 m (medians, 256 randomised robots)
  • Landing (T6) passes: 98 % without fall at 2.5 m/s; foot force 5× body weight over 50 ms, 11× over 20 ms
  • Walking (T2), running 0.8 m/s with 50 ms flight phase (T3) and small 10 cm hop (T4) pass; knee-motor RMS 0.29 / 0.43 N·m
  • Battery: jump push-off needs 36–46 A (up to 67 A) → 4S1P sags below the 12 V cut-off; use 4S2P or ≥ 45 A cells

Concept v1.2

Jump & Run Robot, Concept v1.2: v1.1 hop vs v1.2 charge jump over a 30 cm bar (animated, 2× slow motion)

v1.2 gives the 30 cm Hopper a charge jump: while it crouches (hold A, ~1 s), its own motors wind up knee and ankle springs, a latch holds them, and releasing A fires both legs at once. The key is a four-bar knee drive with the knee motor moved up to the hip, which keeps the motors fast enough near take-off; springs on v1.1's joints alone would gain only ~2 cm because the motors brake. The model gives 24–38 cm centre-of-mass rise and 35–49 cm foot clearance with a tuck; I plan with ~25 cm and ~35 cm, which means 25 cm hurdles reliably, 30 cm hurdles realistically and platforms up to ~20 cm, …

  • Charge jump: hold A crouches and winds ~5.5 J into knee and ankle springs; release A fires both legs
  • Key trick: four-bar knee drive with the knee motor at the hip, so the motors keep pace at take-off
  • Model: 24–38 cm CoM rise, 35–49 cm foot clearance with tuck; plan with ~25 cm / ~35 cm
  • Realistic: 25 cm hurdles reliably, 30 cm hurdles with a tuck, platforms up to ~20 cm

Concept v1.1

Jump & Run Robot, Concept v1.1: Option 2 – the 30 cm Hopper jumps (animated, 3× slow motion)

At toy size the problem flips: landing loads become small, but short legs need very fast joints. Bus servos are fine for walking, but too slow to run or jump at any size from 25 to 50 cm. The smallest robot that can walk is about 25 cm; one that also runs and jumps needs about 30 cm, because fast ~40 mm brushless joints have to fit into the legs. Recommendation: Option 2 Hybrid Hopper, a 30 cm, ~1.4 kg robot for about $470 in parts: 6 fast brushless "smart joints" (hip, knee, ankle) and 6 bus servos on one wire bus, a Pi Zero 2 W and a 3S Li-ion pack, which should run ~0.8 m/s and jump about …

  • Servos walk fine at 25–40 cm but are 4–8× too slow to run or jump
  • Smallest size: ~25 cm for walking, ~30 cm for running and jumping
  • Recommended: Hybrid Hopper, 30 cm, ~1.4 kg, ≈ $470 in parts, runs ~0.8 m/s, jumps ≈ 7 cm
  • Key new part: a ~$36 smart brushless joint that talks on the servo bus (needs PCB and test bench)

Concept v1.0

Jump & Run Robot, Concept v1.0: Option 2 – jump sequence (animated, 2× slow motion)

Concept for a ~1 m humanoid that walks, runs and jumps on Xbox-controller commands: the robot balances itself with an on-board learned gait controller (RL, ~50 Hz), and the pad only sends speed, turn and jump commands over Bluetooth. Three options use low-cost, off-the-shelf quasi-direct-drive motors (RobStride, 17–120 Nm, $145–255 each): Lite (0.8 m, ~15 kg, ≈ $6–7k in parts), Sport (1.0 m, ~22 kg, ≈ $11–13k) and Legs-first (0.9 m, ~17 kg, no arms, ≈ $9–10k). Recommendation: Option 2 Sport, built legs-first: prove running and jumping with the legs-only version first, then add torso and …

  • Proven recipe: low-gear-ratio (QDD) motors, a gait network trained in simulation, and a joystick that only sends commands
  • Recommended: Option 2 Sport (1.0 m, ~22 kg, 18 motors), built legs-first in stages with gates
  • Parts cost: ≈ $6–7k (Lite), ≈ $9–10k (Legs-first), ≈ $11–13k (Sport), plus 6–12 months of team time
  • All 18 joint motors together cost only ~$3.7k at RobStride list prices