Blog · · 5 min read
The parts your PCB order leaves out: batteries, antennas, cameras and cables
An assembled board is not yet a device. The cell, the antenna, the camera module and the cables are bought separately, and each has its own traps: connector series, polarity, flex length, contact side and shipping rules.
The board has passed review, the assembly order is placed, and in a few weeks five finished boards will arrive. Then the next question comes up: what else do I have to buy before this becomes a device?
Usually quite a lot. The factory solders what is on the board. The battery, the antenna, the camera on its flex cable and the cables in between come separately, from other shops, with other lead times. They look simple, but many of the surprises in a first build come from them.
The ZählerSchau meter reader, an open-hardware project on makemachine.ai, is the example in this article. A factory assembles its board. The lithium cell, a pulse capacitor, the camera module, a flex antenna and the radio module, which the assembler does not stock, are bought separately.
Why some parts never see the assembly line
- Batteries are not sent through a reflow oven, and lithium cells ship under dangerous-goods rules. They are added when the device is put together.
- Parts on cables, such as cameras, antennas and displays, sit where the housing needs them, not where the board is.
- Parts the assembler cannot buy stay empty on the board (DNP) and are fitted later. We covered this in Ordering PCB assembly.
The result is a second, smaller shopping list. It deserves the same care as the BOM.
Batteries: chemistry first, then the plug
Cells of the same size can be completely different parts. An AA-size cell may be a 1.5 V alkaline cell, a 3.7 V rechargeable lithium-ion cell (sold as 14500), or a 3.6 V lithium-thionyl chloride primary cell (often sold as ER14505). A device built for a primary cell has no charger. A rechargeable cell of the same size brings the wrong voltage and the wrong safety assumptions. Name the chemistry and the voltage, not just the size.
Then the connection. Cells come bare, with solder tabs, with pins, or with wires and a plug. Cell makers advise against soldering to the cell itself, which is why tabbed and wired versions exist. If your board has a connector, buy the cell with leads and the matching plug, or with tabs and a short lead.
"JST plug" is not a specification. JST PH has a 2.0 mm pitch, JST XH has 2.5 mm (often listed as 2.54 mm), and the two do not mate. Other makers use similar housings with other pitches. Write the series into the parts list.
Polarity is the next trap. There is no universal rule for which pin of a pre-made battery lead carries plus. Measure every lead before it touches the board, and print a plus sign or a pin-1 mark next to the connector.
Lithium-thionyl chloride cells have one more catch. They deliver small currents for years, but bursts poorly, especially after months of rest. Radio and camera need bursts. The usual fix is a hybrid pulse capacitor next to the cell. It is a specialist part, often sold only by industrial distributors, so plan its lead time. Why the cell needs it is explained in Ten years on one battery.
Shipping takes time, too. Loose lithium metal cells are dangerous goods (UN 3090) and may not fly as cargo on passenger aircraft. Many sellers ship them by road or sea, which adds days or weeks.
Antennas: the cable is part of the antenna
Small radio modules usually have a miniature coaxial socket of the U.FL type. It is rated for about 30 mating cycles. Plug it a few times during a build, not every day on the bench.
There are two common choices:
- Flex antennas stick to the inside of the housing and come with a short coaxial lead, often about 100 mm. Nothing goes through the wall.
- Whip antennas screw onto an SMA socket. They need a hole in the housing and a pigtail cable from the module to that socket.
Choose by housing, not by price. A whip antenna does not suit a closed unit that clips onto a meter.
Check the band. Europe uses 868 MHz for this kind of radio, the US 915 MHz. Antennas labeled for both are often tuned somewhere in between, so look up the efficiency at your band in the datasheet. Also check the minimum distance to metal: a flex antenna glued onto a metal surface works poorly.
Camera modules: length, side and lens
Small camera modules on a flex cable look the same across a dozen listings. Three details make them different parts.
- Flex length. The same sensor is sold with flex cables of about 21, 40 and 75 mm. The cable has to reach from the board connector to the lens position, without strain and without a loop that does not fit. In ZählerSchau, the mechanical design needs 38 to 40 mm. The short version does not reach, and the long one has no room.
- Contact side. The contacts sit on one face of the flex. If they face the other way, the pin order on the board is mirrored. The board's pin map holds for one side only, so check the photos, and read the sensor's ID before you take the first picture.
- Lens. Listed fields of view range from about 60° to 160°, and the listed angle is not always what arrives. Buy two or three variants and let a focus test on the real target decide.
Listings rarely include drawings. Measure the module before the housing is final.
The cables you still need
Fewer than expected. The antenna and the camera bring their own. What remains:
- battery leads with the right plug, if the cell comes without one,
- a debug adapter and jumper wires for the programming header. For the common SWD interface these are data, clock, ground, reset and a reference for the target voltage. One adapter serves all units,
- accessory cables only for the variants that use them, such as an optical read head.
A checklist before you click "buy"
- The series and pitch of every connector, not just the brand.
- The polarity of every pre-made lead, measured.
- Cell chemistry and voltage, and whether the cell may be charged.
- Antenna band, type and lead length, and how often the socket may be plugged.
- Camera flex length, contact side and lens angle.
- Lead time and shipping class, especially for lithium cells.
- One or two spares of each, plus variants where a test decides.
How makemachine.ai handles it
On makemachine.ai, the electronics step ends with a list of the parts that are not in the assembly order, with what matters for buying them: connector series, cable length, contact side, and which parts ship as dangerous goods. The mechanical step checks lengths such as the camera flex against the housing. Buying stays with you. The current state of ZählerSchau is on its project page.
Watch hardware get built by AI. Follow public projects on makemachine.ai, read every result in full and get an email when there is something new.
More from the blog
- Will my electronics enclosure overheat? A five-minute heat estimate for a sealed box
- Joining 3D printed parts: screws, heat-set inserts, snap fits or glue?
- Free or paid AI 3D modeling? What you really pay for, and a 30-minute test to compare tools
Open-hardware projects built with AI
- DIY Automatic Plant Watering System: An open-hardware watering system for indoor plants: a small pump, a refillable tank and a soil moisture sensor in each pot keep up to six…
- DIY BBQ Temperature Controller: A temperature controller for charcoal grills and smokers that makers can build themselves. A pit probe, two meat probes and a small fan on…
- ZählerSchau: ZählerSchau is a small, battery-powered unit that clips onto an electricity meter in Germany (water meters via a clamp adapter), takes a…
- Roadstoy: Roadstoy is a remote-controlled toy version of the new Tesla Roadster that can briefly jump and flip using compressed air. It drives on an…
- The forever Washing machine: The forever washing machine is a washing machine offered as a service instead of a product. Customers do not buy the machine but pay for…
- Bike Light: I want to build a bike light that needs no battery. Magnets sit in the spokes close to the hub, and a coil on the fork picks up their…
- Rooficle: I want to develop a light, efficient and affordable e-bike that can be used legally on public roads in Singapore. Its core is an…
- BBQ Modular Grill: I want to design a modular grill. Instead of one sealed block, it is made of separate parts that can each be bought on their own online…
- Go FANUC Go: A mobile base that moves an existing FANUC M-710iC industrial robot (about 560 kg, with a milling spindle at the wrist) out of a room and…
- Jump & Run Robot: I want to build a small, low-cost toy humanoid robot that people can put together themselves. It should be about 30 cm tall, or as small…